What is the correct horizontal distance for the observation

Assignment Help Civil Engineering
Reference no: EM13318235

A distance is measured with an EDM having the instrument /reflector offset constant set to 0mm. The slope distance is reported as 2435.672 m with a zenith angle reading of 90 degrees 34 minutes and 05 seconds. The offset is later determined to be 23mm. What is the correct horizontal distance for this observation.

Reference no: EM13318235

Questions Cloud

Estimate the volume flow rate per meter of width : Water flowing in a wide channel of depth 35 cm undergoes hydraulic jump that resulted in energy dissipation of 72%. Estimate (a) the downstream depth, (b) the volume flow rate per meter of width.
How is culture reflected in movies and television : How is culture reflected in movies and television? Explain the effect of relationships among TV, movies, and electronic games and culture. How is culture reflected in movies and television. Describe the relationship between television, movies, and cu..
Explain aluminium-27 is bombarded with deuterium : What is also produced when aluminium-27 is bombarded with deuterium to give aluminium-28? a. neutron b. proton c. positron d. electron
Find the optimum length of the antenna : A television is tuned to a station broadcasting at a frequency of 6.30×10^7Hz. Find the optimum length of the antenna
What is the correct horizontal distance for the observation : A distance is measured with an EDM having the instrument /reflector offset constant set to 0mm. The slope distance is reported as 2435.672 m with a zenith angle reading of 90 degrees 34 minutes and 05 seconds.
Differences attributable to cultural nuances : Choose two multinational companies, each based in a different home country, and visit their respective websites. Pursue these sites for information that is directed at three company stakeholders: employees, customers, and the community. What differen..
How much energy does it take to assemble these two charges : Two negative charges, Q = -30 \mu C are placed on the x-axis at x = +0.25 m and x = -0.25 m. How much energy does it take to assemble these two charges
Derive a formula relating the variables of the tube : consider the steady viscous flow through a small horizontal tube. for this type of flow, the pressure gradient along the tube should be a function of the dynamic viscosity, the mean velocity and the diameter of the tube
Radiation output-use the stefan-boltzmann law : Calculate the radiation output of the following objects (use the Stefan-Boltzmann law).

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the voids and the density of the grains of soil

An undisturbed saturated soil has a specific weight total of 18.85 kN/m3 and a moisture content of 32.5%. Determine the voids and the density of the grains of soil.

  Determine the maximum possible flame temperature

Consider your cooking gas contains 80% propane and 20% butane. While burning on a cooktop, assume it burns with 200% excess air. If no heat is lost, determine the maximum possible flame temperature.

  Determine height and the velocity of the water downstream

The centres of the piers in a bridge are 8.0m apart. The piers are each 0.8m wide. Water flow under the bridge with an upstream depth and velocity of 4.0m and 4.0m/s respectively. The pier has a drag coefficient Cd = 1.5.

  Determine the magnitude of the total acceleration at time t

Knowing that its speed continues to increase at the same rate until it reaches 100 km/h at point C, 1) determine the speed at point B, and 2) the magnitude of the total acceleration when t = 20 seconds.

  Obtain the elastic moduli of human cortical bone

The cross-sectional geometry of bone varies along its length, although the cross-section can be approximated as hollow and circular, with an average outer diameter of 27 mm and inner diameter of 14 mm

  Find elevation difference in siphon crown nd downstream pool

The siphon crown is 1.2m above the water surface elevation of the reservoir and a length of 10m away from the siphon entrance. If the siphon diameter is 30 cm, the friction factor is 0.2, and the head loss coefficients are 0.2 inlet and 0.1 exit,

  Verify that there are no outliers in the sample data

The measurements of the nominal shear strength (in kN) for a sample of 15 prestressed concrete beams are as follows: 580 400 428 825 850 875 920 550 575 750 636 360 590 735 950

  What will be the concentration of tce in the aqueous phase

The dimensionless henry's constant for TCE at 25 degrees celsius is 0.4. A sealed glass vial is prepared that has an air volum of 4mL overlying an aquesous volume of 36mL.

  Draw the shear and bending moment diagrams for the beam

The beam ABC of length L has two different moments of inertia (2I in AB, I in BC) and a constant elastic modulus E. It is fixed at point A has a roller support at point B and a load P at C. a. Sketch the deflected shape of this beam.

  What is the value of m2 that could be carried by column

The column is braced. The column is required to carry N*=0.75phiNuo kN. What is the value of M2* that could be carried by column considering the slenderness effect. M1*= 0.8M2* Nuo=1000kN r=120mm

  How to design the slab for minimum overall thickness

A one-way solid concrete slab is to be used for a simple span of 16 ft. In addition to its own weight, the slab carries a superimposed dead load of 50 psf and a live load of 75 psf.

  Explain break even stripping ratio

Break Even Stripping Ratio (BESR), Given an underground total mining cost of $8.85 per tonne, surface mining costs of $2.95 per tonne of ore, and surface mining stripping costs of $1.75 per tonne of waste

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd