### What is the conversion rate for parts per million by volume

Assignment Help Civil Engineering
##### Reference no: EM13326298

What is the conversion rate for parts per million by volume (ppmv)conversion. How is this converted into atm, Pa, and torr?

#### Questions Cloud

 Find the speed of the block just before it hits the spring : A 250 g block is dropped onto a relaxed vertical spring that has a spring constant of k = 3.5 N/cm, What is the speed of the block just before it hits the spring What tube diameter is needed if water level in tube is rises : An open, clean glass tube (theta = 0 degrees) is inserted vertically into a pan of water. What tube diameter is neededif they water level in the tube is to rise one tube diameter (dueto surface tension) Explain the following command lines : For example, sed 's/fox/ox/g' file will replace all occurance of fox with ox and not the just the first one in file. Determine the angle-theta of the ramp with a constant speed : A 40lb, .8ft diameter, 1ft tall cylindrical tank slides slowly down a ramp with a constant speed of .1ft/s. The uniform-thicknessoil layer on the ramp has a viscosity of .2lb*s/ft^2. What is the conversion rate for parts per million by volume : What is the conversion rate for parts per million by volume (ppmv)conversion. How is this converted into atm, Pa, and torr Create a subdirectory of the current directory : View without using gunzip but use the tar instead. (Hint: ?nd the right option to use from the man page). What is the concentration in ppm at the downstream reach : Five million gallons per day (mgd) of a conservative substance,with concentration of 10 mg/L is released into a stream having anupstream flow of 10.0 mgd and a substance concentration of 3 mg/L.Assume complete mixing. Create a big file : Give the command-line of displaying the contents of big1.gz using zcat and big2.bz2 but using bzcat without uncompress them. (You may pipe the output to head -10 to avoid lots of output). What is the increase in the dry unit weight of the sand : A sand is densified by compaction at a construction site so thatthe void ratio changes from 0.8 to 0.5. If the specific gravity ofthe soil solids is 2.7, what is the increase in the dry unit weight of the sand

### Write a Review

#### Which communitys transportation is more sustainable

Imagine two small towns of 1,000 people: Blacktop and Parktown. In the urban sprawl that is Blacktop, all the residents own fuel-efficient cars (15 km/liter) and travel an average of 20,000 km per year.

#### Estimate the size of a uniform horizontal welded-steel pipe

Estimate the size of a uniform, horizontal welded-steel pipe installed to carry 14.0 ft^3/sec of water 20 degreesC. The allowable pressure loss resulting from friction is 17ft/mi of pipe length.

#### Determine what is the air void content of core 2

Two tests are taken from the compacted mixture and checked for density. Core 1 had a density of 150 pcf and an air void content of 6.5 %. Core 2 had a density of 151 pcf. What is the air void content of core 2

#### Determine the acceleration of an air particle on the x-axis

The velocity of flow toward the sphere along the longitudinal axis is found to be u = - U0 (I - r~/_xl), where r0 is the radius of the sphere and x the distance from its center.

#### Calculate maximum compressive and maximum tensile stresses

Consider a wide flange steel beam of size W10x60 subjected to a negative bending moment of 24 kip ft. Calculate the maximum compressive and maximum tensile stresses and indicate where the stress will be tensile and where compressive.

#### Estimate the pullout length required for each reinforcement

A continuous geogrid having a reinforcement coverage ratio equal to 100 percent. A continuous metallic grid consisting of W4 bars having a diameter equal to 5.7 mm, a distance between longitudinal bars equal to 150 mm, a distance between transvers..

#### Which method would be most likely to have the conductivity

If an analysis is made of the hydraulic conductivity of a site using permeameter tests of core samples, slug tests of monitoring wells, and pumping tests of production wells, it is often observed that the hydraulic conductivity as measured by each..

#### Determine the hydraulic conductivity of the aquifer

Drawdown at a 0.20 m diameter, fully penetrating well, which has been pumping at the rate of 1000 m^3/day for a long enough time that steady state conditions have been reached, is determined to be 0.70 m.

#### Determine the liquid density in british gravitational units

It is commonly known that there are 16 ounces in 1 lb. Consider a 0.5lbf glass that weighs 1 lbf when filled with 8 ounces of liquid. Determine the liquid density in British gravitational units and in SI units.

#### Determine the horizontal and vertical components of reaction

The winch consists of a drum radius 4 in., which is pin connected at its center C. At its outer rim is a ratchet gear having a mean radius of 6 in. The pawl AB serves as a two-force member (short link) and keeps the drum from rotating.

#### What resistor is needed to create the necessary coil voltage

The available relay for switching a secondary circuit requires 4 volts and has a coil resistance of 145 ohms. If a voltage divider circuit is used to reduce the voltage to activate the relay, what resistor is needed to create the necessary coil vo..

#### Determine acceleration a of frame which will cause tension

The steel ball is suspended from the accelerating frame by the two cords A and B. Determine the acceleration a of the frame which will cause the tension in A to be twice that in B.