What is the coefficient of static friction

Assignment Help Civil Engineering
Reference no: EM13536838

A chair weighing 150 rests on a level floor that is not frictionless. A man pushes on the chair with a force = 43.0 that is directed at an angle of 34.0 with the horizontal. Assume that the chair is stationary but is on the verge of sliding.

Using Newton's laws, calculate , the magnitude of the normal force that the floor exerts on the chair.

What is the coefficient of static friction, between the floor and the chair? Recall that the chair is on the verge of sliding

Reference no: EM13536838

Questions Cloud

The shear enters through the center at the top of the cross : In part (a) of this question we are asked to calculate τmax. In order to do this we separate the cross section at the neutral axis and take the entire upper half (as shown in the cramster solution).
What is fc and d : 5 1/8 in thick laminated timber 24ft long column to support a roof 16 kips and floor load 38kips will be applied at 13' 4" from base.
Determine the minimum required wire diameter assuming : A large steel tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 19,000N. Determine the minimum required wire diameter assuming a factor of safety 5 and that the yield strength of the steel is 900M..
Determine the entrance losses : A 40 cm diameter well has been constructed in a water-table aquifer. A pump capable of continuous discharge at 600 m3/day has been installed to test the well. Observation wells are located 10 meter and 50 meters from the pumped well. After pumping co..
What is the coefficient of static friction : A chair weighing 150 rests on a level floor that is not frictionless. A man pushes on the chair with a force = 43.0 that is directed at an angle of 34.0 with the horizontal. Assume that the chair is stationary but is on the verge of sliding.
When a net amount of work is done on a closed : When a net amount of work is done on a closed system undergoing an INTERNALLY REVERSIBLE process, a net heat transfer of energy from the system also occurs.
What length of time in the model corresponds to one day : A 1:2000 scale tidal model is operated to satisfy Froude’s law. A velocity of 0.02 ft/s is observed in the model. What is the velocity at the corresponding point in the prototype? What length of time in the model corresponds to one day in the prototy..
Determine the rotation of the gear at e : The two shafts are made of A-36 steel. Each has a diameter of 25 mm and they are connected using the gears fixed to their ends. Their other ends are attached to fixed supports at A and B
What is the probability of a water shortage in this city : During the next month, the amount of water available for a city is lognormally distributed with a mean of 1 million gallons and a c.o.v. of 40%, where as the total demand is expected to follow a lognormal distribution with a mean of 1.5 million gallo..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compare total reactor volume require to remove the substance

Compare the total reactor volume required for 90% removal of a substance that decays according to first-order kinetics with a rate constant of 0.05 day -1 in a CM system that contains a single reactor against a system that contains three CM reacto..

  What is the allowable minimum length of the ramp

Using the ADA code, what is the allowable minimum length of the ramp base if base if it is 2 ft high and the code is 1:12

  Determine the tsp emission rate of the power plant

On a clear summer afternoon with a wind speed of 3.20 m/s measured at 100 m elevation, the TSP (total suspended solids) concentration was found to be 1520 ug / m3 at a point 2 km downwind

  What is the composition of the ß phase

A hypothetical A-B alloy of composition 40 wt%B-60 wt%A at sometemperature is found to consist of mass fractions of 0.66 and 0.34for the αand β phases, respectively. If the composition of the α phase is 13 wt% B-87 wt% A, what is the composition ofth..

  Determine the layout for a set of no-3 u-stirrups with fy

A concrete beam that is simply supported sustains a uniform live load of 1.8 kips/ft and a uniform dead load (not including self weight) of 1 kips/ft on a span of 24 ft. Determine the layout for a set of No.3 U-stirrups with Fy=60 ksi and F'c=3.5 ..

  Find height h2 of oil rise in tube by neglecting the mass

The piston rides on a reservoir of oil of depth h1 = 42 mm and specific gravity S = 0.8. The reservoir is connected to a round tube of diameter D2 = 5 mm and oil rises in the tube to height h2. Find h2.

  What is classification of soil using of agriculture textural

What is the classification of the following soil using the united states department of agriculture textural classification chart

  Determine the volume of the solid s by the parabola

Find the volume of the solid S. The base of S is the region enclosed by the parabola y=4-3x^(2) and the x-axis. Cross sections perpendicular to the y-axis are squares.

  What is the dry unit weight and the saturated unit weight

What is the dry unit weight, the saturated unit weight, and the buoyant unit weight, of a soil having a void ratio of 0.5 and a value of Gs of 2.7

  Which of the techniques discussed in class would appropriate

You want to make sure that the hill slope -the earth of which has also been excavated by your teams and the organic soil and vegetation removed- will remain stable for the safety of your workers.

  Determine by trigonmetry the magnitude and direction

knowing that both members are in compression and that the force is 15 KN in member A and 10 KN in member B, determine by trigonmetry the magnitude and direction of the resultant of the force applied to the bracket by member A and B.

  Compute the size of a squeare concrete box culvert to handle

Compute the size of a squeare concrete box culvert to handle a discharge of 25.5 cms. The culvert will have a length of 45.7m with a slope of 0.01 and a maximum headwater depth of 4.57m.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd