What is the 2-4-6-trichlorophenol concentration in ppm

Assignment Help Civil Engineering
Reference no: EM13296998

A 500 L (132 gal) tank contains 255 mg/L 2,4,6-trichlorophenol dissolved in trichloroethylene (TCE). What is the 2,4,6-trichlorophenol concentration in ppm? Assume the temperature of the system is 20 degrees C.

Reference no: EM13296998

Questions Cloud

Will the pce standard of 5 microgram per l be exceeded : If an 18.9 L (5 gallon) bucket of PCE is released (and equally distributed) into a 3.79x10^8 L (100,000,000-gallon) aquifer, will the PCE standard of 5 microgram/L under the Safe Drinking Water Act be exceeded
Compute the molarity of the nacl solution : Calculate the molarity of the NaCl solution in the tank and the volume of the tank in liters. Reaction: NaCl(aq) + AgNO3(aq) -> AgCl(s) + NaNO3
Find the change in length of the bridge : Find the change in length of the bridge for an increase in temperature of 10 degree Celcius
Find how far is the blackboard from her eyes : A student is reading a lecture written on a blackboard. The lenses in her eyes have a refractive power of 61.22 diopters, How far is the blackboard from her eyes
What is the 2-4-6-trichlorophenol concentration in ppm : A 500 L (132 gal) tank contains 255 mg/L 2,4,6-trichlorophenol dissolved in trichloroethylene (TCE). What is the 2,4,6-trichlorophenol concentration in ppm Assume the temperature of the system is 20 degrees C.
What is the tce concentration in mg per cubic meter : The concentration of trichloroethelyne (TCE) in an air sample near a hazardous waste landfill is 34 ppm, the ambient air temperature is 31 degrees C, and the atmospheric pressure is 0.94 atm. What is the TCE concentration in mg/m^3
Determine what was the major principal stress at failure : A consolidated-drained triaxial test on a normally consolidated clay yielded a friction angle of 28°. If the all-round confining pressure during the test was 140 kN/m2, what was the major principal stress at failure.
What is your percentage return on equity for this trade : Suppose you are correct and the stock falls to $70.50 per share at the end of the year. What is your percentage return on equity for this trade?
Calculate the amount of water to be added per cubic meter : An undisturbed soil sample has a total unit weight of 19.4 kN/m3, a dry unit weight of 16.9 kN/m3, and a specific gravity of soil solids (Gs) of 2.69. If the sample could be saturated without changing its porosity, calculate the amount of water (i..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Concentration of moles in the tank solution

HOCL is added to water in a tank as a disinfectant. After equilibrium is reached it is found that the pH of the water in the tank is 8.2 and the gas phase partial pressure is the head space of the tank is 0.2E-7 atm.

  Constant head permeability test

A constant head permeability test was conducted on a clean sand sample. The diameter and length of the test specimen were 10 cm and 12 cm respectively.

  Derive an expression relating effluent concentration

Derive an expression relating effluent concentration to influent concentration, hydraulic residence time, and the reaction rate constant for a zero order reaction in a CSTR at stead-state.

  Determine the net change in storage during the year

Determine the net change in storage during the year if local municipality is allowed to take 100 MGD from the reservoir. You may neglect infiltration and seepage from the reservoir. Sketch a mas blance of the reservoir.

  Determine estimated unknown speed if the data were obtained

In an attempt to estimate the speed of a vehicle just before it hit a traffic signal pole, a traffic engineer measured the length of the skid marks made by the vehicle and performed trial runs at the site to obtain estimate if the coefficient of f..

  Find the direction of flow

A conical tube of length 8 m fixed vertically with its smaller end upwards. The velocity head and pressure head at upper ends are 1.27 m and 2.50 m respectively. The velocity head and pressure head at lower ends are 0.203 m and 5.407 m respectivel..

  Isotropic and homogenous hydraulic conductivity

Assuming an isotropic and homogenous hydraulic conductivity of 0.0001 cm/s what is the magnitude and direction of specific discharge (q)?

  At what rate is the diameter increasing after 5 min

A balloon is being inflated at the rate of 15m^3/min. At what rate is the diameter increasing after 5 min? Assume that the diameter is zero at time zero.

  Determine the basin dimensions

Determine the basin dimensions (width, length, depth) for a detention time of 3 hours and a length to width ratio of 4 to 1. (use English units)

  What is the definition of a customer

What is the definition of a customer? What are some examples of internal and external customers? Is the measurement of customer satisfaction different for internal customers than for external customers?

  Determine specific surfaces in m2 per g units for the sphere

Determine the specific surfaces in m2/g units for the spheres of diameters (a) 10.0 cm, (b) 1.0 cm,(c) 0.1 cm, (d) 0.01 cm. (e) 0.001 cm and (f) 0.0001 cm. Assume the mass density of spheres as 2.5g/cc.

  Explain roman technology and engineering

Roman technology and engineering. Technology and engineering were among Rome's most famous achievements. Describe and explain the importance of Roman technology and engineering

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd