What is tension in the cable connecting the boat to the pier

Assignment Help Civil Engineering
Reference no: EM13299869

A boat tied to a pier shoots water at 60 mph. The initial diameter of the jet is 4 in. What is the tension in the cable connecting the boat to the pier?

Angle of spray 50 degrees off horizontal axis and is spraying toward the pier and pushing the boat away from the pier.

Reference no: EM13299869

Questions Cloud

Find the relationship between light intensity and position : How does the intensity change as position increases? What is the position value corresponding to the highest light intensity, What is the relationship between light intensity and position
How will the stocks be affected : The change will allow the coorporation to report a higher inincome and higher assets although the physical inventory has not changed How will the stocks be affected.
Determine the force acting on the object at given time : An object of mass 126.309172 g executes SHM with an amplitude of 12.426183 cm, Find the force acting on the object at time 1.487176 s
How fast does the hanging mass rise : The rope wrapped around the outer diameter of the disk is pulled at a constant speed of 1.06 m/s. If the outer radius is 1.39 cm, how fast does the hanging mass rise
What is tension in the cable connecting the boat to the pier : What is the tension in the cable connecting the boat to the pier Angle of spray 50 degrees off horizontal axis and is spraying toward the pier and pushing the boat away from the pier.
Calculate the moment of inertia of the rod : A thin rod with length L has a linear density that varies as D = dm/dx = Ax, Calculate the moment of inertia of the rod for an axis at the left end, perpendicular to the rod. Compare your result to that of a uniform rod
Calculate actual cost-earned value and planned value : he project duration is planned for 20 weeks. The project budget is $40,000 and is planned to be spent on a level bases through out the project. You are at the end of week 10, the accounting department tells you the project has spent $19,500
Define the gas expands irreversibly against a fixed pressure : Consider a perfect gas with Cvm = 28.0 J/mol-K trapped in a piston/cylinder arrangement with cross-section area of 250.0 cm^2. The gas expands irreversibly against a fixed external pressure of 1.0 atm adiabatically
Determine the decay constant and the half-life : A sample 114 nd has a mass of 0.055395 kg and emits an average of 2.36 alpha particles per second. Determine the decay constant and the half-life

Reviews

Write a Review

Civil Engineering Questions & Answers

  Horizontal distance between the points

A runs slope a distance of 156.777 m from one point to another point at a rate of +1.5%. What is the corresponding horizontal distance between the points?

  Where the maximum ground level concentration would occur

a power plant burns 150,000 tonnes (1 tonne = 1,000 kg) of coal each year. The coal has 2.5% sulfur content, and the air pollution control equipment removals approximately 94% of sulfur. Assume 10% of the sulfur content ends up in the ash.

  Maximum acceptable tensile service load

Compute the maximum acceptable tensile service load T that may act on a single angle L6x4x3/4 that is welded along only one leg to a gusset plate; thus, there are no holes. The service load is three times the dead load. Solve for a0 A36 steel.

  Determine the value of gravity in units of meters

if a ball is dropped from a height of 800 cemtimeters, and the impact velocity is 41 feet per second, determine the value of gravity in units of meters per second.

  Determining specific gravity

The cross sectional dimensions of a 4-ft-long wood member at 30% moisture content is 1.5 in. x 7.5 in., and its weight is 11 lb. At oven-dry condition, its dimensions and weight are 1.35 in x 6.8 in., and 10.2, respectively. What is its specific g..

  Calculate the force

Calculate the force (in Kn) a punch press must exert if it is to punch out a large washer from a strip of 5-mm thick sheet steel with an ultimate shear strength of 400 MPa. The washer dimensions are as follows: hole diameter is 27 mm. outside diam..

  Explain metallurgical balance in mineral processing

Metallurgical balance in mineral processing, Assume 2000 short tons of ore were mined, 200 tones were rejected as waste and the tonnage accepted for metallurgical treatment

  Determine longitudinal and hoop stresses in the copper pipe

Typical water supply at a faucet in any building is conveyed in copper pipe that is ½" in inside diameter, with a wall thickness of 0.040". If the water pressure is 50 psi and the valve is closed (meaning that water is not flowing)

  Calculating energy for vacancy formation

The number of vacancies in some hypothetical metal increases by a factor of 4 when the temperature is increased from 1090 K to 1140 K. Calculate the energy (in J/mol) for vacancy formation assuming that the density of the metal remains the same ov..

  Determine the length of time

The 20-lb cart B is supported on rollers of negligible size. If a 10-lb suitcase A is thrown horizontally on it at 10 ft/s, determine the length of time that A slides relative to B, and the final velocity of A and B. The coefficient of kinetic fri..

  Define holographic mobile phones

A young engineer has invented holographic mobile phones and has approached a venture capital company to invest in it. The venture capital company considers the product to be an all or nothing product

  Derive an equation for the undrained shear strength of clay

if a clay slope at a construction site fails derive an equation for the undrained shear strength of the clay given that the shear reistance along L of the slope can be given as: (SuH0)/ sin beta

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd