What is normally consolidated clay

Assignment Help Civil Engineering
Reference no: EM13535611

1.Q> What is normally consolidated clay?

2.Q> What is Formative classification system for soils ( Just write the name)

3.Q> What are differences between seepage & discharge velocity?

4.Q>Compute the nominal shear strength of an M10 x 7.5 of A 572 grade 65 steel

Reference no: EM13535611

Questions Cloud

Design the shear reinforcement : Problem Statement: A rectangular beam having b = 10 in. and d = 17.5 in. spans 15 ft face to face of simple supports. It is reinforced for flexure with three
Identify the contaminants on site and explain : Identify the contaminants on site and explain their hazards in relation to the proposed design and its construction. Describe the ‘In-situ’ and Ex-situ’ treatments that could be used and their relative merits
Briefly outline with the use of neat labelled sketches : It is proposed to make a new pedestrian access running directly south from University Square to Silvertown. The physical barriers that need to be overcome are the Royal Docks and the City Airport runway.
Determine the pressure between the sleeve and cylinder when : Maximum shear stress both in the tube and sleeve is 16000 psi. Calculate the fluid pressure, and determine the pressure between the sleeve and cylinder when the fluid pressure is absent.
What is normally consolidated clay : Compute the nominal shear strength of an M10 x 7.5 of A 572 grade 65 steel
Compute the probable settlement of the building : The construction of a multi storied building started in January 1989 & was completed in June 1990. The total consolidation settlement of the building was estimated to be 8 cm.
Determine the quantify the losses in this system : At Point A, in a pipeline carrying water (γ=62.4 lb/ft^3) the diameter is 4.0 ft, the pressure is 10 psi, and the velocity 4 ft/s. At point B, 6ft higher than point A, the diameter is 2 ft and the pressure is 2ps
What is the average crack spacing for that reinforcement : Compute the effective composite modulus of subgrade reaction (please consider the subbase, the presence of a relatively shallow rock foundation, and the potential loss of support)
Develop a preliminary design, including flow rates : Develop a preliminary design, including flow rates, pipe sizes, and pipe slopes for a trunk sewer to be laid in the development shown in the accompanying figure from 6th to 1st Streets along Peavy Avenue.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the produce of inertia for the shaded area

Determine the produce of Inertia, Ixy, for the shaded area to the right using integration. Use the parallel axis theorem to find Ibarxy, the product of inertia with respect to the centroidal axes.

  Determine the required pumping rate of the construction

It is required to dewater a construction site 80 m by 80 m. The bottom of the construction will be 1.5 m below the initial water surface elevation of 90 m. Four pumps are to be used in 0.5-m diameter wells at the four corners of the site.

  Determine modulus of elasticity of concrete by aci formula

Determine the Modulus of Elasticity of Concrete by the ACI formula for a concrete cylinder that has a unit weight of 120pcf (1920kg/m^3) and a compressive strength of 3000 psi (21MPa).

  How to determine the efficiency of the pump

Water is pumped at a rate of 1.57 cfs from one large open tank into another through a 6 in diameter cast iron pipe 400 ft long. The water level in the second tank is 160 ft above the level of the first tank and the discharge end of the pipe is sub..

  What was involved in the first far-reaching

what was involved in the first far-reaching, comprehensive study of Earth's oceans?

  Determine cir and fdr with foamed asphalt

The pavement structure consists of 160 mm of hot-mix asphalt (HMA), 150 mm of granular base and 450 mm of subbase placed over silty clay subgrade. The pavement is 20 years old and its current PCI is 50.

  Calculate the power input to the pump in kw

A 60 MW Rankine steam power cycle in Iceland uses reheat. The system is comprised of a single adiabatic pump, a boiler using geothermal energy, two adiabatic turbine stages and a condenser.

  Determine what are the dimensions to replace the pond

water from a waste water treatment plant is released into a receiving pond that has a volume of 5 ac-ft. one of the reasons for doing this is to assure that the chlorine residual is below 0.1mg/L before the water is released to a stream as require..

  Determine the system curve for the pump system

The entrance is square edged, and the elbows are 90o. There is a fully opened gate valve on the suction side and the discharge side, and there is a swing type check valve on the discharge side. Determine the system curve for the pump system.

  What is the bod concentration at the outflow of the pond

A pond is used to treat a dilute municipal waste-water before the liquid is discharged into a river. The inflow to the pond has a flow rate of Q = 4,000 m3/day and a BOD concentration of Cin = 25 mg/L.

  Determine distance form the exterior face of the interior

The distance l, which is the distance between the outside face of the exterior support at the left-hand end of the beam and the center of the interior support at the right-hand end, is 30ft; the width of the exterior support at the left is 16in.

  Show how kh and kow can be used to describe koa

Show how Kh, and Kow can be used to describe Koa. You must show how the concentration units for all equilibrium distribution ratios either cancel or remain to give the final value for Koa. Octonal-air partitioning coefficient (Koa = C(octanol)/C(a..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd