What are the recorded values of r dot

Assignment Help Civil Engineering
Reference no: EM13555025

At the bottom of a loop in the vertical plane an airplane has a horizontal velocity of 315 mi/h and is speeding up at a rate of of 10ft/s^2. The radius of curvature of the loop is 1mi. The plane is being tracked by radar at O. What are the recorded values of r dot, r double dot, theta dot and theta double dot for this instant?

Reference no: EM13555025

Questions Cloud

Determine the pressure that develops in the container : A rigid-walled cubical container is completely filled with water at 40 0F and sealed. The water is then heated to 100 0F. Determine the pressure that develops in the container when the water reaches this higher temperature
Draw a mass balance diagram and estimate the monthly mass : Each month the speedy dry Cleaning company buys 1 barrel (0.160 m^3)of dry cleaning fluid . Ninety percent of the fluid is lost to the atmosphere and 10 percent remains as residue to be disposed of
Determine how many rpms is it doing : You rev your car's engine to 2600 (). a) If you change the period of the engine to 0.038 , how many rpms is it doing
What is the maximum acceleration from rest for the car : A newly designed car has a 9.0 ft wheelbase, is rear wheel drive, and has a center of gravity 18 inches above the road and 4.3 ft behind the front axle. the car weighs 2450 lb, the mechanical efficiency of the drivetrain is 90% and the wheel radius i..
What are the recorded values of r dot : At the bottom of a loop in the vertical plane an airplane has a horizontal velocity of 315 mi/h and is speeding up at a rate of of 10ft/s^2. The radius of curvature of the loop is 1mi
What was the students associated perception/ reaction time : An engineering student is driving on a level roadway and sees a construction sign 500 ft ahead in the middle of the roadway. the student strikes the sign at a speed of 25 mi/h.
Compute what is the speed of the bullet before impact : A 0.004-kg bullet is fired into a 0.200-kg block of wood at rest on a horizontal surface. what is the speed of the bullet before impact
Devise an absolute temperature scale where the boiling point : Devise an absolute temperature scale where the boiling point of water at 1 atmosphere (101 kPa) pressure = 100 degrees in your scale What is the ice point of water in your scale?
Evaluate the maximum magnitude of the acceleration : A 0.60- mass attached to a vertical spring of force constant 150 oscillates with a maximum speed of 0.30. Find the maximum magnitude of the acceleration

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the minimum necessary clearance height

Determine the minimum necessary clearance height of the overpass and the resultant elevation of the bottom of the overpass over the PVI. (ignore the cross-sectional width of the overpass)

  What is the difference among cement plaster

If the tangents intersect at an angle of 40 degrees, what is the highest degree of curve that can be used?..how to solve this problem using chord basis formula?

  Determine its velocity for t along a straight line

A particle moving along a straight line is subjectd to a deceleration a=(-2v^3)m/s^2 where v is in m/s. If it has a velocity v=8 m/s when t=0, determine its velocity when t=4s.

  How long did the electric heating system run that night

A passive solar house that is losing heat is outdoors at an average rate of 50,000 kJ/h is maintained at 22oC at all times during a winter night for 10h.

  Calculate braking force rb at wheel rim for each system

A bicycle rider would like to compare the effectiveness of candilever hand brakes (use figure a) versus V brakes (figure part b). (a) Calculate the braking force Rb at the wheel rim for each of the bicycle brake systems.

  Design the pins so that ledge can support doug and jeremy

Assume the ledge has the dimensions shown and is attached to the building with a series of equally spaved pins around the circumference of the building.

  Compute the ratio of the nominal flexural strength

Compute the ratio of the nominal flexural strength of the beam to the maximum service load moment, and compare your findings to the ACI load factors and strength reduction factor.

  Derive an equation and solve for the volume v of a cstr

derive an equation and solve for the volume V of a CSTR, operated isothermically for the second-order reaction 2R->P, where rR=-kC^2 R. Data are k=6.0 L/mol-s, CRin=0.005 mol/L, CRout=0.0005 mol/L, and Q=100 L/s.

  Determine the min coefficient of static friction required

If the coefficient of static friction between the man's shoes and the pole is u=0.6, Determine the minimum coefficient of static friction required between the belt and the pole at A in order to support the man.

  Design a balcony slab exposed to the weather

Design a balcony slab exposed to the weather. The cantilevered span is 8 ft and the service live load is 100 psf. fc' = 4,000 psi, fy = 60,000 psi.

  Is the actual flow in the pipeline laminar or turbulent

Oil flows through the Trans-Alaska pipeline. Because oil is viscous, you might think that the flow is laminar. (a) What is the minimum flowrate (m3/s) for which the flow would likely be laminar.

  Determine the drawdown after 2 days of puming

a well is located in a confined aquifer. the transmissivity of the aquifer is 1200 m^2/d and the storativity is 0.0005. the flow rate is 4000 m^3/d. At a distance 75m from the well,

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd