Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.Coal has about 5% sulfur. How many pounds of sulphur would be emitted from coal-fired power plants in the united states in 3 years? (each year. U.S electricity production in about 0.28 x 1012 watts, and coal has an energy content of about 30 x 106 J/kg. Note that 1J = 1W-sec). Show all work
2.Why is the torque on A and the torque on AB opposite? Wouldn't they be the same? How do we know which direction the torque is applied at A to begin with? It's not specified.
3.What are the bearings of the sides CD,DE,EA, and AB if the side CB has a bearing S 20° 44’ 36” W, point A is westerly of B and interior angles in each apex are as follows: A = 95° 14’ 23”; E=81° 16’ 54”; D=74° 55’ 19”; C=220° 22’ 22”; B=68° 11’ 02”
A nozzle is designed to linearly accelerate the fluid from V1 to V2 (i.e., V = ax +b, where a and b are constants). Determine the local acceleration, the convective acceleration, and the total acceleration at point 1 and 2 at t = 0.
A 1-mile-long racetrack is to be designed with a 1/4-mile turns at each end. Determine the superelevation rate for a design speed of 70 mph, assuming f=.20.
For a 30ft simply supported beam, there is a uniform load of 1.5 k/ft. along the length and two point loads of 20 kips each spaced at (from x=0 to x=30ft left to right) x=10ft and x= 20 ft.
A floor is to be supported on hardwood timber joists that are spaced at 0.5m centres and span 5.0m. The joists support flooring 20mm thick and an applied live load of 2kN/m2 Design a typical joint 50mm wide
A u-tube manometer is used to measure the pressure of a vessel under vacuum. Assume the manometer is open to atmospheric pressure (101.325 kPa) and the density of the fluid in the manometer is 12.0 g/cm3.
Suppose that a person who boards the elevator on the ground floor gets off on the fifth floor. Assuming that the elevator has achieved operating speed by the time it reaches the second floor and that it is still moving at its operating speed as it..
As a consulting engineer you are hired to evaluate the operation and the unit processes within the plant and make recommendations for improvements. You are asked to consider the following units.
determine the number of bricks and cubic feet of mortar required for 100 square feet of wall. the ties are to be spaced 16 inches on center vertically and 24 inches on center horizontally
A 600 ft vertical crest curve crosses a 4 ft diameter pipe at rightangles at station 110+85. The PVI of the vertical curve is station110+00 and elevation 1098.4 ft with an incoming tangent grade of1.2% and an outgoing tangent grade of -1.8%.
if the aircraft is encountering a steady side wind of speed vw=10 mi/hr , at what angle (a) should the pilot direct the aircraft so that the absolute velocity is parallel to the runway
A steel tube has an outside diameter of 2.5 inches and an inside diameter of 2.375 (1/8" thick). If it transmits 35 hp when turning at 2700 rpm, what is the maximum shear stress
Discharge from an orifice of 75mm diameter is 0.02 m^3/s under a constant head of 3 m. An external mouthpiece of the same diameter is installed that raises the coefficient of contraction from 0.63 to 1.0.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd