Water is the working fluid in an ideal rankine cycle steam

Assignment Help Mechanical Engineering
Reference no: EM13640309

Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lbf/in2 and 1000°F. The condenser pressure is 2lbf/in^2. Both turbine and pump have isentropic efficiencies of 85%. The working fluid has negligible pressure drop in passing through thee the steam generator. The net power output of the cycle is 1 x 10^9 Btu/hr. Cooling water experiences a temperature increase from 60°F to 76°F, with negligible pressure drop, as it passes through the condenser. Determine

a) The mass flow rate of steam, in lb/h.
b) The rate of heat transfer, in Btu/h, to the working fluid passing through the steam generator.
c) The thermal efficiency.
d) The mass flow rate of cooling water, in lb/h.

 

Reference no: EM13640309

Questions Cloud

The short horizontal diversion tunnel is 3 m in diameter : you are in charge of the construction site of a new dam. extremely heavy rainfall starts and bureau of meteorology
An element has 3 stable isotopes with natural abundances : an element has 3 stable isotopes with natural abundances of 11 17 and 72. the masses of those isotopes are 19.9 21.9
Determine the magnitude of the velocity of the third : a 210-kg projectile fired with a speed of 142 ms at a 69.0 degrees angle breaks into three pieces of equal mass at the
The concentration of a dye and concentration of bleach : the concentration of a dye and concentration of bleach naoh was determined experimentally by using beers law. the rate
Water is the working fluid in an ideal rankine cycle steam : water is the working fluid in an ideal rankine cycle. steam enters the turbine at 1400 lbfin2 and 1000degf. the
The unit is electric and utilizes a resistance heater 120 v : the recovery time of a hot water heater is the time required to heat all the water in the unit to the desired
What is the probability that exactly half of the beech : use the following information to answer the three items belowin a certain large forest 25 of all the beech trees show
The pressure in the air above the two tubes is now : two identical vertical tubes each 1.00 cm in diameter and 50.0 cm tall are each filled with a liquid. the liquid in
Plot pressure angle as a function of cam rotation angle 0 : for a modified sine profile with cam interval of 120 degree and rise of 10mm use b0.25 c0 d0.75. plot pressure angle as

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Would it be a possible to use a normal domestic

would it be a possible to use a normal domestic refrigerator as a heat source for a small hot tub or whirlpool? if so

  An insulated cylinder is initially filled with saturated

an insulated cylinder is initially filled with saturated r-134a vapor at a specified pressure. thenbsprefrigerant

  Find the exit temperature of the air in degc find the

refrigerant-22 is condensed from 120degc 1.40 mpa to saturated liquid using air at 24degc 1.00 bar. the air absorbs

  What is the flow rate of water when the gauges show a

a vertical pipe conveying water tapers from 50 mm in diameter at the top to 25 mm in diameter at the bottom in a length

  The convective heat transfer coefficient for the exhaust

an axhaust stack thermocouple is inserted into a 20 cm long well made of 5mm-o.d. 0.7 mm-wall-thicknes aisi 316

  The rotor has a weight of 100 lb with its center of mass

an electric motor weighing 750 lb and running at 1800 rpm is supported on four steel helical springs each having eight

  Black sell his house to gray with gray agreeing to take

black is purchasing a house under a real estate mortagage held by the white mortgage black is obligated to make a

  The inlet velocity is 5 fts and the inlet and exit

water at 200 lbfin2 and 300 f is throttled adiabatically through a valve to 30 lbfin2. the inlet velocity is 5 fts and

  If the isentropic efficiency of the compressor is 80

argon gas enters a adiabatic compressor at 20psia and 90 f with a velocity of 60 fts and it exits at 200 psi and 240

  A pure aluminum conical section with cross sectional

a pure aluminum conical section with cross sectional diameter of d ax12. a 0.5meters12. the small end of the cone is

  Determine the minimum no of teeth required on pinion in

determine the minimum no of teeth required on pinion in order to avoid interference which is to gear with 1 a wheel to

  The heat transferred over the first 6 cm of the plate is 20

air flows at a constant velocity over a flat plate which is heated over the entire length at a fixed temperature. the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd