The short horizontal diversion tunnel is 3 m in diameter

Assignment Help Mechanical Engineering
Reference no: EM13640313

You are in charge of the construction site of a new dam. Extremely heavy rainfall starts and Bureau of Meteorology hydrologists tell you that beginning at about 8 AM, 2 GL per hour (2 x 106 m3 per hour) will flow into the dam. The lake behind the dam has approximately vertical walls and a surface area of 1 x 106 m2. At 8 AM, you measure the water level behind the dam: it is 6.5 m below the top of the incomplete dam, and if it overflows, it could sweep away construction equipment on the top. Water from the lake is draining freely and steadily through the dam's diversion tunnel. The short, horizontal diversion tunnel is 3 m in diameter, has its centerline 40 m below the top of the incomplete dam, and exits to atmospheric pressure. How much time have you got to move equipment from the top before it overflows?

Reference no: EM13640313

Questions Cloud

A hoodlum throws a stone vertically downward with an : a hoodlum throws a stone vertically downward with an initial speed of 12.0 ms from the roof of a building 33.0 m above
Wat is the numeric value of k if the pmf is given as px : what is the numeric value of k if the pmf is given as px k2 for x
After 700 s have elapsed determine its velocity vector and : a snow mobile has a position vector 42.1 m at 98.0 degrees counter clockwise from the x axis and velocity of 5.35 ms at
What would be the effect on your calculated mass percent : what would be the effect on your calculated mass percent recovery of cu if you did not completely react the mg in the
The short horizontal diversion tunnel is 3 m in diameter : you are in charge of the construction site of a new dam. extremely heavy rainfall starts and bureau of meteorology
An element has 3 stable isotopes with natural abundances : an element has 3 stable isotopes with natural abundances of 11 17 and 72. the masses of those isotopes are 19.9 21.9
Determine the magnitude of the velocity of the third : a 210-kg projectile fired with a speed of 142 ms at a 69.0 degrees angle breaks into three pieces of equal mass at the
The concentration of a dye and concentration of bleach : the concentration of a dye and concentration of bleach naoh was determined experimentally by using beers law. the rate
Water is the working fluid in an ideal rankine cycle steam : water is the working fluid in an ideal rankine cycle. steam enters the turbine at 1400 lbfin2 and 1000degf. the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd