The overall heat transfer coefficient is 500 wm2k the

Assignment Help Mechanical Engineering
Reference no: EM13640733

A counterflow, concentric tube heat exchanger is designed to heat water from 20 to 80 °C using hot oil, which is supplied to the annulus at 160 °C and discharged at 140 °C. The thin-walled inner tube has a diameter of Di = 20 mm, and the overall heat transfer coefficient is 500 W/m2K. The design condition calls for a total heat transfer rate of 3000 W.

a. What is the length of the heat exchanger?

b. After 3 years of operation, performance is degraded by fouling on the water side of the exchanger, and the water outlet temperature is only 65 °C for the same fluid flow rates and inlet temperatures. What are the corresponding values of the heat transfer rate, the outlet temperature of the oil, the overall heat transfer coefficient, and the water-side fouling fact?

Reference no: EM13640733

Questions Cloud

A swift moving hawk is moving due west with a speed of 30 : a swift moving hawk is moving due west with a speed of 30 ms 5.0 s later it is moving due north with a speed of 20 ms.
Compound b is burned in a calorimeter containing 15l of : compound b is burned in a calorimeter containing 1.5l of water.when 50.0g of compound b is burned in the calorimeter
Compute the values of the three quartiles and the : the following data give the speeds of 13 cars measured by radar traveling on the interstate highway i-84.67 72 63 66 76
A hotel elevator ascends 200 meters with maximum speed of 5 : a hotel elevator ascends 200 meters with maximum speed of 5 ms. its acceleration and deceleration both have a magnitude
The overall heat transfer coefficient is 500 wm2k the : a counterflow concentric tube heat exchanger is designed to heat water from 20 to 80 degc using hot oil which is
Several statistical tests have a way to measure effect size : several statistical tests have a way to measure effect size. what is this and when might you want to use it in looking
An 87-o resistor and a 64-o resistor are connected in : an 87-o resistor and a 64-o resistor are connected in series across a battery. the voltage across the 87-o resistor is
Air at 293 k and 1 bar is blown over the rod at 25 ms : horizontal aluminum rod 1 cm in diameter and 10 cm long has both ends maintained at 363 k. air at 293 k and 1 bar is
An optically active ie chiral compound with the : an optically active i.e. chiral compound with the formulac6h12o2 shows a broad strong bandat 3400 cm-1 and a strong

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd