The heat transfer from the compressor to the surroundings

Assignment Help Mechanical Engineering

Reference no: EM13627564

Refrigerant 134a enters a compressor at 200kPa, 100% quality and exits at 1MPa, 60 degrees centigrade. The speed of the R-134a at the inlet is 40m/s, the speed at the exit is 10m/s and the mass flow rate of the R-134a through the compressor is 0.08kg/s. The heat transfer from the compressor to the surroundings is 0.63 kW. Include the change in the kinetic energy of the R-134a and compute the power input needed to operate the compressor.

Reference no: EM13627564

Previous Q& A

The centerboard of a sailboat is 25m long and has a chord

the centerboard of a sailboat is 2.5m long and has a chord of 1m. approximate the centerboard as a flat plate in water

What is the measure of angle theta measured clockwise from

an unpolarized light beam traveling along the x-axis is sent into a system of three polarizers. the polarization axis

A 150-h inductor is connected in series with a 200nbspomega

a 1.50-h inductor is connected in series with a 200nbspomega resistor through a 15.0-v dc power supply and a switch. if

The thin-walled pipe has an inner diameter of 05 cm and a

the thin-walled pipe has an inner diameter of 0.5 cm and a thickness of 0.025 cm. if it is subjected to an internal

A statewide real estate agency farm associates specializes

a statewide real estate agency farm associates specializes in selling farm property in the state of nebraska. its

The pressure at the exit of the turbine is 10 kpa and the

superheated steam at 8 mpa and 480oc leaves the steam generator of a vapor power plant. heat transfer and frictional

A circular steel bar is axially loaded it has a diameter of

a circular steel bar is axially loaded. it has a diameter of 2 in. a modulus of elasticity of 29x103ksi and a shear

Nitrogen gas enters a diffuser at 100 kpa and 110 degrees c

nitrogen gas enters a diffuser at 100 kpa and 110 degrees c with a velocity of 205 ms and leaves at a 110 kpa and 45

Provide an example of a situation where you could utilize

provide an example of a situation where you could utilize correlation analysis calculating the coefficient of

A piston cylinder device initially contains 06 kg of steam

a piston cylinder device initially contains 0.6 kg of steam with a volume of 0.1 m3. the mass of the piston is such

Reviews

Write a Review

Message

Similar Q& A

For the vapor power cycle steam enters the at 3 mpa and 500

for the vapor power cycle steam enters the at 3 mpa and 500 c and leaves at 70 kpa and 200 c. the system is operating

To conserve water and energy a flow reducer is installed in

to conserve water and energy a flow reducer is installed in the shower head shown here. if the pressure at point 1

The sphere is cooled by 20oc air with a convection heat

a 20 cm diameter sphere is made of a heat-generating material that produces 106 wm3. the sphere is cooled by 20oc air

The specific heat of the gas follows the relationship given

an ideal gas flows through a device at steady state. the temperature of the gas at the inlet is 20c and its velocity

Compute the convective heat-transfer coefficient the

a liquid food is being heated in a tubular heat exchanger. the inside pipe wall temperature is 110degc. the internal

An 800 ft ship has a displacement of 37600 tons and the

an 800 ft ship has a displacement of 37600 tons and the area defined by the waterline is 38000 ft2. a will the ship

The thermal efficiency of the cycle and the net specific

Determine the thermal efficiency of the cycle and the net specific work. Assume each turbine stage isentropic efficiency to be 99% and assume the FWH is open.

Water vapor at 30 mpa and 300c state 1 is cooled to

water vapor at 3.0 mpa and 300c state 1 is cooled to 200cstate 2 then is isothermically compressed to 2.5mpa state 31.

Obtain an algebraic expression for the speed reached by the

a rocket motor is used to accelerate a kinetic energy weapon to a speed of 3500 mph in horizontal flight. the exit

Calculate the overall train value

calculate: a) the overall train value. b) the output rational speed at shaft 5. c) the output torque at shaft 5. Relevant gear data is= NA= 17, NB= 36, NC= 19, ND= 41, worm E = double lead, worm G = triple lead, NH= 37?

A projectile is fired at an angle of 62deg from the

a projectile is fired at an angle of 62deg from the horizontal with a velocity of 704 ftsec. if it lands 4.75 seconds

You are an industrial hygienist for a large distributor of

you are an industrial hygienist for a large distributor of industrial compressed gases who was evacuated to baton rouge

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

User Account

All Pages