A ships hull is 150m long as has a wetted area of 5000 m2

Assignment Help Mechanical Engineering
Reference no: EM13627566

A ship's hull is 150m long as has a wetted area of 5000 m^2. When it is encrusted with barnacles, it requires 7000 hp to overcome friction drag and move at 15 knots in seawater at 20C. What is the average roughness due to the barnacles? If the hull was cleaned up in a dry dock, what would be the Maximum speed with the same propulsive power?

Reference no: EM13627566

Questions Cloud

What would happen if you place a 1m by 2 m sheet of : what would happen if you place a 1m by 2 m sheet of aluminum extruded and place it on the roof of your car driving at
Light of wavelength 455 nm is incident on a narrow slit the : light of wavelength 455 nm is incident on a narrow slit. the diffraction pattern is viewed on a screen 3.11 m from the
Using a 001 significance level test the inspectors claim : the acme bacon company distributes bacon in packages labelled 500 grams. an inspector randomly selects 49 of these
The compressed liquid water enters the desuperheater at : a desuperheater is a steady-flow adiabatic mixing process that mixes superheated water vapor with colder liquid water
A ships hull is 150m long as has a wetted area of 5000 m2 : a ships hull is 150m long as has a wetted area of 5000 m2. when it is encrusted with barnacles it requires 7000 hp to
In a double-slit interference experiment the wavelength is : in a double-slit interference experiment the wavelength is 467 nm the slit separation is 0.110 mm and the screen is
The heat transfer from the compressor to the surroundings : refrigerant 134a enters a compressor at 200kpa 100 quality and exits at 1mpa 60 degrees centigrade. the speed of the
The centerboard of a sailboat is 25m long and has a chord : the centerboard of a sailboat is 2.5m long and has a chord of 1m. approximate the centerboard as a flat plate in water
What is the measure of angle theta measured clockwise from : an unpolarized light beam traveling along the x-axis is sent into a system of three polarizers. the polarization axis

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Consider a cylindrical nickel wire 19 mm in diameter and 32

consider a cylindrical nickel wire 1.9 mm in diameter and 3.2 times 104 mm long. calculate its elongation when a load

  If the dew point is 10 oc determine the thickness of the

in a pharmaceutical plant a copper pipe kc 400 wm.k with inner diameter of 20 mm and wall thickness of 2.5 mm is used

  A catheter is a specialised needle intended for long-term

a catheter is a specialised needle intended for long-term insertion into a vein in a patients arm. engineers are

  A group of students launches a model rocket in the vertical

a group of students launches a model rocket in the vertical direction. based on tracking data they determine that the

  If the copper sphere is initially at 1000k perform an

a 1-in diameter pure copper sphere is suspended in a room where the walls and air are all at 300k. the natural

  A computer cooled by a fan contains eight pcbs each

a computer cooled by a fan contains eight pcbs each dissipating 10w power. the height of the pcbs is 12 cm and the

  What is the quality of the steam at the point when the

steam contained in a piston amp cylinder appartus is initially at 200kpa and x0.8. this pressure is sufficient to hold

  What is the flow rate of water when the gauges show a

a vertical pipe conveying water tapers from 50 mm in diameter at the top to 25 mm in diameter at the bottom in a length

  Determine the concentration in weight percent of gap that

gallium arsenide gaas and gallium phosphide gap both have the zinc blende crystal structure and are soluble in one

  If the coefficient of restitution between each car is85

at a amusement park there are 180kg bumper cars a b and c that have riders as shown with masses 40 kg 60kg and 30 kg

  Calculate the reynolds number for water dynamic viscosity

calculate the reynolds number for water dynamic viscosity of 7.98 10-4 nsm2 flowing through a rectangular pipe 4 cm

  Estimate the mean and variance of the distribution of

2. a certain production process produces two parts a bearing and a shaft. in the final assembly the shaft and the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd