The flow rate 54 cubic meters per minute the pump

Assignment Help Mechanical Engineering
Reference no: EM13621564

A pump is used to move water from a lower reservoir to an upper reservoir. The water surface elevation in the upper reservoir is 30 meters above the water surface elevation in the lower reservoir. The pipe is steel , 1000m long , with a diameter of 400mm. The flow rate 5.4 cubic meters per minute. The pump efficiency is 60%. Ignore minor losses. Determine the shaft power of the pump in kilowatts.

Reference no: EM13621564

Questions Cloud

In the second community a random survey of 90 households : a firm wanted to see if there was a significant difference between two neighboring communities in terms of the mean
The temperature of the water is 50 f determine the darcy : flow and pressure measurements are used to estimate the friction factor for a pipeline. the length of the pipeline
It is illuminated normally by white light analysis of the : a thin film having an index of refraction of 1.5 is surrounded by air. it is illuminated normally by white light.
The mean weight for a random sample of 16 ball bearings is : assume that a simple random sample has been selected from a normally distributed population and test the given claim.
The flow rate 54 cubic meters per minute the pump : a pump is used to move water from a lower reservoir to an upper reservoir. the water surface elevation in the upper
Two lenses one converging with a focal length equal to 10 : two lenses one converging with a focal length equal to 10 cm and another diverging with a focal point of -15 cm are
The voltage would be lower due to the current flow what is : a fuel cell stack consists of 75 fuel cells arranged in series each one 12cm2 in size. the stack operates at 80.c and
What is the difference betweeen the angles of incidence of : the index of refraction for silicate flint glass is 1.66 for violet light that has a wavelength in air equal to 400 nm
One year ago peyton purchased 3600 shares of broncos stock : one year ago peyton purchased 3600 shares of broncos stock for 101124. today he sold those shares for 26.60 a share.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Consider a thermal energy reservoir

Consider a thermal energy reservoir at 1500 K that can supply heat at a rate of 150,000 kJ h-1. Determine the exergy of this supplied energy, assuming an environmental temperature of 25 oC.

  What is the minimum acceptable coefficient of friction

A 782 pound 4WD vehicle is designed to clime a 16 degree ramp. What is the minimum acceptable coefficient of friction between its tires and the ramp surface?

  Determine the moment of the force about point b

A 90N force is applied to control rod AB as shown. Knowing the length of the rod is 225mm, determine the moment of the force about point B by resolving the force into components along AB and in direction perpendicular to AB?

  How many grams of na3po4 will be needed

how many grams of Na3PO4 will be needed to produce 250 mL of a solution of a solution that has a concentration of Na+ ions of 1.5 M.

  A particle which moves with curvilinear motion has

a particle which moves with curvilinear motion has coordinates in meters which vary with time t in seconds according to

  In an air-standard otto cycle the air at the beginning of

in an air-standard otto cycle the air at the beginning of the compression stroke is at 95 kpa and 22 degrees c and the

  The manometer shown above in problem 1 above contains water

the manometer shown above in problem 1 above contains water and kerosene. with both tubes open to the atmosphere the

  Find the the acceleration of each mass

Two equal masses are connected on either side of a pulley. One of the masses rests on an inclined plane with angle of inclination of b. The other one hangs in mid air.

  A horizontal cantilever of length l supports a load w

a horizontal cantilever of length l supports a load w uniformly distributed along its length. the cantilever is proped

  The radial loads of both gears are in the same plane and

a shaft is to be designed to support the spur pinion and helical gear shown in the figure on two bearings spaced 700 mm

  Find the velocity and acceleration of the end of the bar

a 600 mm diameter wheel rolls without slipping on a horizontal surface as shown. rod ab is attached to the wheel at a

  What is the allowable minimum length of the ramp

If the ramp height is 2ft. Using the ada code, what is the allowable minimum length of the ramp?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd