Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1. Water vapour at 90kPa and 150°C enters a subsonic diffuser with a velocity of 150m/s and leaves the diffuser at 190kPa with a velocity of 55m/s and during the process 1.5 kJ/kg of heat is lost to surroundings. Determine (i) The final temperature (ii) The mass flow rate. (iii) The exit diameter, assuming the inlet diameter as 10cm and steady flow. 2. A 0.5-m3 rigid tank contains refrigerant-134a initially at 200 kPa and 40 percent quality. Heat is now transferred to the refrigerant until the pressure reaches 800 kPa. Determine (a) the mass of the refrigerant in the tank and (b) the amount of heat transferred. Also, show the process on a P-v diagram with respect to saturation lines. 3. It is proposed to use water instead of refrigerant-134a as the working fluid in air- conditioning applications where the minimum temperature never falls below the freezing point. Would you support this proposal? Explain. 4. A commercial refrigerator with refrigerant-134a as the working fluid is used to keep the refrigerated space at-30°C by rejecting its waste heat to cooling water that enters the condenser at 18°C at a rate of 0.25 kg/s and leaves at 26°C. The refrigerant enters the condenser at 1.2 MPa and 65°C and leaves at 42°C. The inlet state of the compressor is 60 kPa and -34°C and the compressor is estimated to gain a net heat of 450 W from the surroundings. Determine (a) the quality of the refrigerant at the evaporator inlet, (b) the refrigeration load, (c) the COP of the refrigerator, and (d) the theoretical maximum refrigeration load for the same power input to the compressor. 5. In absorption refrigeration cycles, why is the fluid in the absorber cooled and the fluid in the generator heated? How is the coefficient of performance of an absorption refrigeration system defined? 6. Can water be used as a refrigerant in air-conditioning applications? Explain.
a spring-mass is excited by a force f0sinomegat. at resonance the amplitude is measured to be 0.58 cm. at 0.80 resonant
during a particular thunderstorm the electric potential difference between a cloud and the ground is vcloud - vground
the average electrical generating capacity of the united states was about 475000 mw in 2007. if trends continue this
refrigerant 134a at -10degc 1.4 bar and a mass flow rate of 280 kghr enters an insulated compressor operating at steady
The spool has a mass of 75 kg and a radius of gyration . It rests on the inclined surface for which the coefficient of kinetic friction is . If the spool is released from rest and slips at A, determine the initial tension in the cord and the angul..
a 2.5kg iron specific heat capacity is 450jkg0c component at 1000c is quenched by dipping it into a water tank
1. a process water with a specific heat capacity of 4.182 k.1 kg-i k-1 flows at a rate of 0.050 kg s-i through a heat
a cord is wound in the slot of cylinder a. mass b moves downward with a velocity of 6 m. assume no slipping of the
An electronics company has a contract to deliver
a piston cyfinder system containing 0. 5kg of air is compressed from a volume of 0. 35 m3 to a volume of 0. 1 m3. if
how does the energy use for the typical family vehicle compare with that for the typical hot water heater? what are the
Helium enters subsonically and flows isentropically through the converging-diverging duct. Compare the values of Ma, T/T0, and P/P0 for helium with those for air at several locations in the duct. Use 0.163 ≤ Ma ≤ 3.221.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd