Specify the hydraulic retention time for a pfr designed

Assignment Help Civil Engineering
Reference no: EM13298870

A series of experiments was conducted in a batch reactor to test the disinfection by chlorine of E. coli. In each experimental run, the concen tration of free available chlorine was varied and the time required to kill 99% of the organisms was determined. The results showed that a CT value of 200 min mg/L was sufficient to achieve a 2-log removal.

(a) In Chick's law, what value of k corresponds to a chlorine concentration of 1 mg/L?

(b) Specify the hydraulic retention time for a PFR designed to achieve 99.9% removal of E. coli. with a chlorine concentration of 1 mg/L.

(c) Specify the hydraulic retention time for a CMFR designed to achieve 99.9% removal of E. coli. with a chlorine con centration of 1 mg/L

Reference no: EM13298870

Questions Cloud

What are the primary limitations on the extent : What are the primary limitations on the extent to which insurance can reduce the risks faced by a corporation?
Determine the friction drag on one side of the plate : Water flows past a triangular flat plate oriented parallel to the free stream as shown. Integrate the wall shear stress over the plate to determine the friction drag on one side of the plate. Assume laminar boundary layer flow.
Explain reducing nitro benzene with iron and hcl : One synthetic preparation of aniline involves reducing nitro benzene with iron and HCL, and then steam distilling the resultant aniline at 99 degrees Celsius. How much aniline codistills with each gram of water during the steam distillation.
Estimate extent of laminar boundary layer flow along wing : An airplane flies at a speed of 360 mph at an altitude of 5000 ft. If the boundary layers on the wing surfaces behave as those on a flat plate, estimate the extent of laminar boundary layer flow along the wing in feet.
Specify the hydraulic retention time for a pfr designed : In each experimental run, the concen tration of free available chlorine was varied and the time required to kill 99% of the organisms was determined. The results showed that a CT value of 200 min mg/L was sufficient to achieve a 2-log removal.
Determine the power loss due to resistance in the line : A high-voltage transmission line with a resistance of 0.33 omegacap.gif/km carries a current of 1040 A. What is the power loss due to resistance in the line
Calculate relative velocity of solute front through aquifer : Calculate the relative velocity of a solute front that is flowing through an aquifer. The organic carbon partitioning coefficient (Koc) is 6 mL/g and the friction of organic carbon in the soil is 2%.
Determine the resulting current in the wire : If the wire is heated to 36.0°C while the 7.0-V potential difference is maintained, what is the resulting current in the wire
Calculate the temperature coefficient of resistivity : A wire 3.00 m long and 0.450 mm2 in cross-sectional area has a resistance of 41 omegacap.gif at 20°C. what is the temperature coefficient of resistivity

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the resistance coefficient k for a ball-type

Calculate the resistance coefficient K for a ball-type check valve placed in a 2-in schedule 40 steel pipe carrying 650 gal/min of oil (sg = 0.90)

  Determine the magnitude and direction of the force

Determine the magnitude and direction of the force P in so that the resultant of P and the 900N force is a vertical force of 2700N directed downward using.

  Formulate a linear program for blend mix

Formulate a Linear Program for Blend Mix at Bluegrass Distillery, The Bluegrass Distillery produces custom-blended whiskey

  How many identical reactors does sony music company require

The plant currently has one CMFR for removal of chromium. How many more identical reactors does the sony music company require to meet the regulatory requirements for chromium discharge of 0.01 mg/L into the Pitman Sewer?

  Identify the risk factors

Tacoma Narrows Bridge. Conduct either a qualitive and quantitive risk assessment on this project. Identify the risk factors that you consider most important for the suspension bridge construction. How would you assess the riskiness of this project..

  Largest principal stresses and maximum shear stress

The shaft diameter is 100 mm. Calculate the largest principal stresses and maximum shear stress that will occur in the shaft.

  What are the concentrations of cl- and br-

AGNO3 is added to a solution containing 0.001 mol Cl- amd 0.001 mol Br- per liter. What are the concentrations of Cl- and Br- remaining when AgCl just begins to precipitate?

  Define water circulating through it at the rate

A 4 X 8-ft solar collector has water circulating through it at the rate of 1.0 gallon per minute while exposed to sunlight with intensity 300 Btu/ft^2-hr.

  Calculate the distance traveled by the prey

Calculate the distance traveled by the prey from the time it is dropped until the time it hits the ground. Express your answer correct to the nearest tenth of a meter.

  Four-lane undivided multilane highway

A four- lane undivided multilane highway ( two lanes in each direction) has 11- ft lanes and 5- ft shoulders. At one point along the highway there is a 4% upgrade that is 0.62 mi long.

  Define energy transfer in mechanical systems

Energy transfer in mechanical systems, A wheel is 800mm in diamiter and has a mass of 1000kg. on a horizontal surface without skidding, the vehicle accelerates uniformly at 0.5m/s^2 for 5 seconds.

  Describe the measurements that would have to be taken

describe the measurements that would have to be taken and the equations that would have to be used to determine G23, V32, and E2 for a specially orthotropic transversely isotropic material from a single tensile test.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd