Specific gravity of solids in this soil

Assignment Help Civil Engineering
Reference no: EM13533403

1.The total volume of a soil specimen is 120 cm3 and its total mass is 220g. Specimen porosity is 0.4 and specific gravity of solids is 2.66   Determine the following: (a) water content, (b) void ratio, (c) degree of saturation, and (d) dry density. 

2.A saturated soil has a void ratio of 0.7   Specific gravity of solids in this soil is 2.67      

Determine (a) the saturated unit weight, and (b) dry unit weight.  Use units of ft and lb.

Reference no: EM13533403

Questions Cloud

The lower surface is stationary and contains : Two infinite parallel horizontal surfaces are seprated by a film ofSAE 10W oil at T=10 C that is d=0.0144 in. thick . The uppersurface moves with speed V
Find the balls initial velocity upward : A baseball is hit so that it travels straight upward after being struck by the bat. Find the ball's initial velocity in m/s upward
Is this a good settling sludge or this operator in trouble : A waster water treatment operator runs a sludge volumeindex test in a liter cylinder and finds at the end of 30 minutessettling, the solids occupy 200mL. He knows the suspendedsolids concentration in his aeration tank from which he got thesample is 4..
Evaluate the work done by the resistive force : A bicyclist rides 3.01 km due east, while the resistive force from the air has a magnitude of 7.71 N and points due west. Find the work done by the resistive force during the round trip
Specific gravity of solids in this soil : The total volume of a soil specimen is 120 cm3 and its total mass is 220g. Specimen porosity is 0.4 and specific gravity of solids is 2.66   Determine the following: (a) water content, (b) void ratio, (c) degree of saturation, and (d) dry density.
Calculate the work done by the pushing force : A person pushes a 12.3-kg shopping cart at a constant velocity for a distance of 16.5 m on a flat horizontal surface. calculate the work done by the pushing force
Find the normal force and the acceleration of the object : A block of mass 20kg is sliding down an incline plane with no friction. Find the normal force and the acceleration of the object
What is the residence time in this tank : A sample of dry sand having a unit weight of 105 pcf and a specific gravity of 2.70 is placed outdoors.  During a storm, the sample degree of saturation increased to 40% while its total volume did not change.  Determine the total unit weight and wate..
What will be his speed upon emerging : A cyclist is coasting at a steady speed of 16m/s but enters a muddy stretch where the effective coefficient of friction is 0.55. What will be his speed upon emerging

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the thickness for the slab and select the size

A solid one-way slab is to be used for a framing system Column spacing is 33 ft, with regularly spaced beams occurring at 11 ft center to center. Superimposed dead load on the structure is 50 psf and the live load is 75 psf.

  Determine the cycle length and distributuion of green

A simple four-leg intersection needs a 2-phase fixed-time signal. The critical flows in the N-S and E-w directions are 600 and 400 veh/hr, respectively, with a 0.95 peak-hour factor.

  In the non-inertial cs fixed at the top of the vertical

the linkage shown below is made up of two 3-kg rectangular members 0.4 m by 0.1 m and is flying through the air. at the

  Compute the flexural strerangth if the load is fracture

A three point bending test is performed on a glss specimen having a rectangular cross section of hight d =6 mm and width b = 12 mm the distance between support points is 45mm.

  Give reason why plumbing should be considered by management

A chemical plant produces a process wastewater that contains a relatively high concentration of a small number of nontoxic organic compounds, but very low concentrations of solids or salts. It has no odor.

  Determine the perpendicular distance d from the line to the

A line passes through the points (20m, 16m) and (-1m, -4m).  Determine the perpendicular distance d from the line to the origin O of the system of coordinates.

  Design a three story office building

Design a three story office building

  Explain why the atomic packing factor of fcc steel is less

Iron can exist in the FCC or BCC structure. For FCC iron, the crystal lattice parameter is a=0.3515nm and the atomic packing factor is 0.74. In an FCC structure, iron atoms have an atomic radius of 0.1263nm.

  Sketch process on p-v diagram clearly labeling final states

5 Kg of water at 1.2 MPa, 120oC is contained in a frictionless piston-cylinder device. The water is heated until its temperature reaches 250oC. a) a)Determine the work performed in kJ

  Determine whether the discharge of the towns wastewater

The Big Bear town council has asked that you determine whether the discharge of the town's wastewater into the Salmon River will reduce the DO below the state standard of 5.00 mg/L at Little Bear, 5.79 km downstream.

  Will crack widths be affected by the air entrainment

Will crack widths be affected by the air entrainment?

  Basics of economies of construction

For a metal and wood structure, how would the economies of construction be obtained (pertaining to the mean and standard deviation of a probability of failure graph)?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd