User Account

All Pages

Shown with the agilent function generator

Assignment Help Other Engineering
Reference no: EM131077685

FOR "JACK JONES" ONLY!!!! Capacitive Reactance LAB

  1. Watch the videos
    • Week 2 Video Lecture - Capacitive Reactance
  2. Consider the circuit below:

    For each value of the frequency in the chart below, perform calculations for Ic, Vc and Xc.

    Frequency Calculated Ic Calculated Vc Calculated XC Measured IC Measured Vc XC (From Measured)
    100 Hz            
    500 Hz            
    1000 Hz            
    1500 Hz            
    10000 Hz            
    20000 Hz            
  3. Construct the circuit with MultiSIM using a 10% tolerance for the capacitor. Replace the AC source shown with the Agilent Function Generator.

    *Note: One way to set the tolerance on a component is to do the following:

    1. Double-click on the component and select the Value tab.
    2. Select or enter the desired value in the Tolerance field and click OK.
  4. Complete the chart by adjusting the values of frequency and measuring Ic and Vc using the Agilent Multi-meter and then from these values calculating the value of Xc in the last column.

    *Note: Current is measured in series with the capacitor and voltage is measured in parallel (across) the capacitor. Capture screenshots showing the measured values of Ic and Vc using the Agilent Multi-meter.

  5. Discuss the following:
    1. Describe the relationship between the frequency and the capacitive reactance.
    2. What effect does frequency have on Ic and Vc for a fixed value of capacitance in this circuit?
    3. For a frequency of 1000Hz, what would be the effect of increasing the value of the capacitor on the current Ic and the voltage Vc?
    4. Why is it necessary to measure current in series with a device and voltage across it?
    5. Why is it necessary to determine Xc from measured values of current and voltage as opposed to measuring it directly with a digital multi-meter? (It may be helpful to perform research on the internet to gain more insight into the topic of this question.)

Reference no: EM131077685

Questions Cloud

What would you have done differently in terms of scope : Now, it is time to reflect on what went well and what didn't go so well. Based on feedback throughout the course, what would you have done differently in terms of scope, resources, and / or schedule, and why?
What is the probability that a union member who had surgery : What is the probability that a union member who had surgery was advised to do so by a second doctor?
What is the probability that this person is a housewife : If an eligible voter who participated in the survey and voted in the election is selected at random, what is the probability that this person is a housewife?
Define two basic coping strategies for dealing with stress : Briefly define the two basic coping strategies for dealing with stress and give a brief example of how you use, or could use, these in your personal life.
Shown with the agilent function generator : Construct the circuit with MultiSIM using a 10% tolerance for the capacitor. Replace the AC source shown with the Agilent Function Generator.
Type of printing error : Major textbook publisher has a contract with a printing company. Part of the contract stipulates that no more than 5 percent of the pages should have any type of printing error.
Describe how you would measure pain : Describe the differences between nociception, pain, pain behavior, and suffering. Find and illustrate examples of how people can have nociception without pain, pain without pain behavior, and pain without suffering.
Who is involved in an accident is under 25 : Who is involved in an accident is under 25?
Write down the test hypotheses : A study on the pay of CEO's examined the percentage increase in cash compensation of the CEO's of 104 companies, adjusted for inflation, in recent years. The mean percentage increase in real compensation was and sample standard deviation of 5.3%. ..

Reviews

Write a Review

Other Engineering Questions & Answers

  Function accomplished with the r/w~ control signal

Question 4. 4. In the standard set-up of a keypad, the four rows are connected to 9S12G128 output ports, and the four columns are connected to input ports with internal pull up resistors enabled. In your own words, describe how the scanning progra..

  Analog design and in particular op amp design

Discuss why analog design and in particular op amp design is a fundamental skill that will be required far into the future.

  What dead times are encountered in a heat exchange process

What dead times are encountered in a heat exchange process and what process and equipment gains affect the operation of a heat exchanger.

  Characterize the production performance of bakken wells

Characterize the production performance of Bakken Wells. You need to correlate the decline rates of Bakken wells to well/reservoir/completion Parameters, and finally make contour maps.

  Players and spectators wear the same clothes

Consider a tennis match in cold weather where both players and spectators wear the same clothes. Which group of people will feel colder? Why?

  Design a system to improve the safety

Consider the hazards of performing maintenance on machinery and design a system to improve the safety when doing the maintenance function.

  Create an edge-triggered d flip-flop

To simulate the operation of a circuit used to create an edge-triggered D flip-flop. To test the operation of a 74LS74 D flip-flop. To test the operation of a 74LS112 J-K flip-flop

  Draw the output voltage waveform

2. A power-supply transformer has a turns ratio of 5:1. What is the secondary voltage if the primary is connected to a 120 V rms source?

  Using microsoft project software develop a wbs

This assignment will be a deliverable oriented towards the grouping of project elements which organizes and defines the total scope of your project

  Determine the minimum cable force t and critical angle

Determine the minimum cable force T and critical angle ? which will cause the tow truck to start tipping, i.e., for the normal reaction at A to be zero. Assume that the truck is braked and will not slip at B. The truck has a total mass of 4 Mg and..

  Dawes road and jeff hamilton road intersection redesign

Dawes Road and Jeff Hamilton Road Intersection Redesign. The Mobile County and Alabama Department of Transportation desire a redesign of the intersection of Jeff Hamilton Road and Dawes Road due to safety issues and poor level of service.

  Develope a strategic vision and sense of mission

Why is it important to develope a strategic vision and sense of mission before proceeding? Why is it important to politically know the key stakeholders and ensure they are in agreement before proceeding?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd