User Account

All Pages

Question regarding the design characteristics of the motor

Assignment Help Mechanical Engineering
Reference no: EM13870111

It is required to design the DC motor to run a small size electric vehicle to be used inside an airport building to help the transportation of old people. The vehicle is supposed to carry a maximum of 4 persons at the highest speed of 60 Km/hour. The engine is driven by a 200 V battery capable to energize the motor for 120 Km before being recharged. The efficiency of the motor must be between 85 to 90 percent. The motor shaft diameter is expected to be within (0.2 to 0.4 m). Give the size of the battery required in AH (Ampere Hour). Choose and estimate all the design characteristics of the motor, finally display all the power flow diagram results including efficiency and speed  regulation of the motor. Give all assumptions taken.

Reference no: EM13870111

Questions Cloud

Breach of the copyright act to make a copy of a film : a) Is it a breach of the Copyright Act to make a copy of a film shown on television? Discuss. b) Is it a breach of copyright to download a piece of music from the Internet? Discuss.
Prepare the november adjusting entry for bad debts : Prepare the November adjusting entry for bad debts. Prepare a schedule to estimate an appropriate year-end balance for the Allowance for Doubtful Accounts. Prepare the December 31 adjusting entry. Show how the various accounts related to accounts rec..
What is selective incorporation : REVIEW QUESTIONS  1. What is selective incorporation? Total incorporation? Which reflects current law? 2. Name three rights that have been incorporated and one that has not
Analyze interview data for recurring themes : Consider evidence of quality in results. Analyze interview data and look for recurring themes. Complete a write-up of the experience
Question regarding the design characteristics of the motor : Choose and estimate all the design characteristics of the motor, finally display all the power flow diagram results including efficiency and speed  regulation of the motor. Give all assumptions taken.
Contract without specifics regarding time of order : Supplier, Inc., a large wholesaler, had a  contract with Grocery, Inc. Supplier, Inc. sued Grocery, Inc. for breach of contract when Grocery, Inc. failed to place an order for goods by a specific date as specified in the contract. Each order was to b..
Why as output increases total cost eventually rises faster : Briefly explain why as output increases total cost eventually rises faster than total revenue for a perfectly competitive firm.
The purpose of the system and the problem : In an organization that you are familiar with, identify the systems being used in terms of the purpose of the system and the problem it helped in solving
Concept of working in hospitality as performative labour : Discuss the concept of working in hospitality "as performative labour" to a practical hospitality context. Choose and apply ONE of the following concepts: Sexualised/gendered experience e.g. Bedroom restaurant in Melbourne

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the effect of the propane addition on the mole

a system of propane and n-butane exists in two phase vapor liquid equilibrium at 10 bar and 323 k. the mole fraction

  Find the discharge coefficient for flange taps

the reynolds number of a fluid flowing through a 5-cm-diameter, square-edged orifice plate meter within a 15-cm pipe is 250,000. Find the discharge coefficient for flange taps.

  Helium at atmospheric pressure and 30 degc flows across a

helium at atmospheric pressure and 30 degc flows across a square plate at a free stream velocity of 15 ms. calculate

  The data from table to evaluate change in specific entropy

Consider a system consisting of liquid water initially at T1 = 318 K, p1 = 3.5 bar undergoing a process to a final state at T2 = 353 K, p2 = 1.5 bar. Use appropriate equation with the data from the table to evaluate change in specific entropy.

  A cylinder containing a mixture of 90 n2 and 10 c2h6 and a

cylinder containing ch4 c2h6 and n2 has to be prepared in which the ratio of the moles of ch4 to c2h6 is 1.3 to 1.

  Calculate its elongation

Consider a cylindrical titanium wire 3.0 mm in diameter and 2.5 x 104 mm long. Calculate its elongation when a load of 500N is applied, assuming that the deformation is totally elastic.

  Determine rate of heat transfer from the wire and if air

a 2-cm long section of a 3-mm in diameter wire is maintained at a constant surface temperature of 370c. the wire is

  For each claimed set of data listed below determine whether

a power cycle operates between hot and cold reservoirs at 1000 k and 300 k respectively. for each claimed set of data

  Determine the final mass of the tank

An insulated rigid tank contains 5 kg of helium gas at 440 kPa and 31C. A valve is now opened, and helium is allowed to escape until the pressure inside drops to 200 kPa. Assuming the helium remaining inside the tank has undergone a reversible, adiab..

  A slender rod is at rest in vertical position with lenght

a slender rod is at rest in vertical position with lenght of 1.5m. then a force of 50 n. is applied at the bottom tip.

  Estimate the uncertainty in indicated speed

An auto speedometer is graduated in 5 mph increments and has an accuracy rated to be within ±4%. Estimate the uncertainty in indicated speed at 60 mph.

  A viscous fluid flows past a flat plate such that the

a viscous fluid flows past a flat plate such that the boundary layer thickness of a distance d from the leading edge is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd