Prove that the ratio of depth to width of the strongest beam

Assignment Help Mechanical Engineering
Reference no: EM131061859

Prove that the ratio of depth to width of the strongest beam that can be cut from a circular log of wood having diameter d is 1.414.

Reference no: EM131061859

Questions Cloud

Describe the unique challenges faced by this population : Describe the unique challenges faced by this population. Examine specific factors that contribute toward addiction for this population.
Terminating and repeating decimals investigation : Terminating and Repeating Decimals Investigation Part A 1. Complete the table by converting each decimal to a fraction. Show your work.
Determine the velocity and position of load b after 3 s : The velocity and position of load B after 3 s,
What can be the impact on the business : Tell Mr. Lee, in detail, the main internal control weaknesses in the situation described. What can be the impact on the business because of these weaknesses - Give him suggestions on what needs to be done to rectify this situation
Prove that the ratio of depth to width of the strongest beam : Prove that the ratio of depth to width of the strongest beam
Facts the national aeronautics and space administration : FACTS The National Aeronautics and Space Administration (NASA) is an independent federal agency charged with planning and conducting "space activities." One of NASA's facilities is the Jet Propulsion Laboratory (JPL) in Pasadena, California, which..
Calculate the gdp for both countries : BUS700 MACROECONOMICS  Calculate the GDP for both countries and discuss the usefulness of these data in deciding which, if any, of these two countries is likely to be experiencing an economic recession.
Demonstrate key supply chain challenges for businesses : This summative assignment is designed to allow the student to demonstrate their learning from the course.  The assignment will allow the student the opportunity to demonstrate key supply chain challenges for businesses in 2016, to explain why they..
Which infraorders include monkeys : Using your book and any notes from class, Compare Homo Erectus, Homo Neanderthalensis, and Homo Sapiens terms of the following features: Cranial Features (at least 3 features), skeletal features (at least 3 features), and Tool use/culture. You may..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Difference between a francis turbine and a pelton wheel

Calculate the power supplied by the module when it operates at each of the points, X, Y and Z of Figure 1. Comment briefly on the significance of the relative values of your three answers.

  According to the electric bill the heat pump utilizes 3000

at steady state a heat pump maintains the interior of a house at 77f by transferring to it 30 kw of heat from the

  The water is then cooled until the piston is on the lower

water is contained in a vertical cylinder fitted with a frictionless piston and two sets of stops. the volume is 0.1m3

  Water exiting the condenser of a power plant at 38ordmc

water exiting the condenser of a power plant at 38ordmc enters a cooling tower with a mass flow rate of 4.5 x 107 kgh.

  A ships hull is 150m long as has a wetted area of 5000 m2

a ships hull is 150m long as has a wetted area of 5000 m2. when it is encrusted with barnacles it requires 7000 hp to

  A 4 lb block with an initial velocity of 5 fts is sliding

a 4 lb block with an initial velocity of 5 fts is sliding down a 30 degree slope before being slowed by a spring. if

  What is the shear strain

A cylindrical shaft if 80mm long with a 20mm dia and is fixed to a wall at one end. If a shear force of 10kN is applied vertically at the free end, what is the shear strain?

  Maximum normal stress and maximum shear stress direction

an element of material is subjected to the following state of stress.sigmax-40 sigmay100 sigmaz30tauxy-50 tauyz12

  Determine the a amount of paddle-wheel work in btu after 45

an insulated rigid tank initially contains 1.8 ibm of helium at 82 f and 45 psia. a paddle wheel with a power rating of

  A steam turbine is limited to a maximum inlet temperature

a steam turbine is limited to a maximum inlet temperature of 800.degc. the exhaust pressure is 0.0100 mpa and the

  Calculate the density of the air in the round section

At one section in an air distribution system, air at 14.7 psi and 100degree F has a velocity of 1200 ft/min a and the duct is 12 in x12 in square. At another section the duct is round with a diameter of 18 inches and the velocity is 900 ft/min. Calcu..

  Determine the power required in hp to heat the house using

a building for which the heat transfer rate through the walls and roof is 1350 btuh per degree temperature difference

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd