Determine the velocity and position of load b after 3 s

Assignment Help Mechanical Engineering
Reference no: EM131061861

A pulley and two loads are connected by inextensible cords as shown. Load A has a constant acceleration of 10 in/s2 and an initial velocity of 8 in/s, both directed upward. Determine

(a) The number of revolutions executed by the pulley in 3 s,

(b) The velocity and position of load B after 3 s,

(c) The acceleration of point D on the rim of the pulley at time t = 0.

Reference no: EM131061861

Questions Cloud

Calculate the products of inertia of cross sections : Many cross sections can be approximated by a series of rectangles as shown. Write a computer program that can be used to calculate the products of inertia of cross sections of this type with respect to horizontal and vertical centroidal axes.
Normal distribution diagrams : Consider the two probabilities listed below. Indicate which probability is greater and explain the reasons for your decision. First: The probability that a sample of 25 sixth-graders will have a sample mean of more than 110 words per minute.
Describe the unique challenges faced by this population : Describe the unique challenges faced by this population. Examine specific factors that contribute toward addiction for this population.
Terminating and repeating decimals investigation : Terminating and Repeating Decimals Investigation Part A 1. Complete the table by converting each decimal to a fraction. Show your work.
Determine the velocity and position of load b after 3 s : The velocity and position of load B after 3 s,
What can be the impact on the business : Tell Mr. Lee, in detail, the main internal control weaknesses in the situation described. What can be the impact on the business because of these weaknesses - Give him suggestions on what needs to be done to rectify this situation
Prove that the ratio of depth to width of the strongest beam : Prove that the ratio of depth to width of the strongest beam
Facts the national aeronautics and space administration : FACTS The National Aeronautics and Space Administration (NASA) is an independent federal agency charged with planning and conducting "space activities." One of NASA's facilities is the Jet Propulsion Laboratory (JPL) in Pasadena, California, which..
Calculate the gdp for both countries : BUS700 MACROECONOMICS  Calculate the GDP for both countries and discuss the usefulness of these data in deciding which, if any, of these two countries is likely to be experiencing an economic recession.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd