Propane is contained in a piston-cylinder assembly

Assignment Help Mechanical Engineering
Reference no: EM13717750

A quantity of propane is contained in a piston-cylinder assembly. this working fluid undergoes a process starting from an initial state of 2.0 mpa and 60oc. at the end of the process the pressure of the propane is 1.0 mpa and the specific entropy is 0.089 kj/kgk higher than at the start of the process.

Determine the temperature of the propane at the end of the process.

Reference no: EM13717750

Questions Cloud

Calculate the molality and the mole fraction : Calculate the molality and the mole fraction of each of the following solutions: (a) 1.00 mol CH20 and 10.0 mol H2O, (b) 2.00 mol CH3OH and 500g H2O, and C) 100 g C2H5OH and 500g H2O
What is the molality of the hydroxide ions : The solubility of Ba(OH)2 * 8H2O in water at 15 degrees c is 5.6g per 100 g of water. (A) what is the molality of a saturated solution at 15 degrees c? What is the molality of the hydroxide ions?
Water is stored in a water tower at an elevation : Water is stored in a water tower at an elevation of 1804 m above sea level. The foundation of your apartment building is at an elevation of 437 m above sea level and you live on the 9th floor, with each floor having a height of 3.3 m.
Write a balanced nuclear reaction for the decay of neptunium : Np-237 (atomic mass= 237.0 amu) has a half life of 2.20x10^6 years. The isotope decays by alpha emission. a) Write a balanced nuclear reaction for the decay of neptunium-237.
Propane is contained in a piston-cylinder assembly : A quantity of propane is contained in a piston-cylinder assembly. this working fluid undergoes a process starting from an initial state of 2.0 mpa and 60oc. at the end of the process the pressure of the propane is 1.0 mpa and the specific entropy is ..
Determine the clausius and antoine constants : Develop the spreadsheet pages to determine the Clausius and Antoine constants for methanol and water in the range of 1 - 5 atm total pressure.
Calculate the volumes of weak acid and its conjugate base : Calculate the volumes of weak acid and its conjugate base needed to make the pH buffer solution below. 500mL of pH buffer solution, pH=7.50, 0.50 Sodium bicarbonate.
Calculate the number of ml of each stock solution : Make 200 mL of an aqueous solution with 150 mM KCL and 100 microM CaCl2. Premade stock solutions: 1.000 M KCl and 0.250 M CaCl2. Calculate the number of mL of each stock solution needed to make the solution
Compute delta-v for each maneuver and total minimum delta v : A re-supply satellite is launched from NASA/Wallops Island into a circular orbit of radius 6678 km with inclination of i = 38. In order to rendezvous with the ISS, the re-supply satellite needs to both raise it's altitude to 400 km, via a Hohmann tra..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd