Prepare electronically-generated free-body diagram of system

Reference no: EM131261817

Human Biomechanics Assigment

Overview

This document outlines the BME/ISE 3211 Human Biomechanics I Course Project in which biostatics analysis is used to design rehabilitation parameters for a patient with a torn distal biceps tendon. Each student will construct a free-body diagram of the human elbow/tendon system, perform static analysis of the system with an external load placed in the hand, calculate theoretical tendon tensions for a set of specified angles and loads, display data graphically, and design rehabilitation parameters within constraints set by an injury specialist. A formal report is to be submitted to a dropbox on Pilot with all relevant info and conclusions.

Background

You are a consulting biomedical/industrial engineer assisting an employer in a prominent regional manufacturing company. An employee has torn a distal biceps tendon and must undergo rehabilitation. An injury specialist has performed tests and advises that the injured tendon should not be subjected to forces exceeding 650 N during rehabilitation.

The employee's job requires routine handling of parts ranging from 3-6 kg. During manipulation of these parts, the employee must extend the arm with supinated palm and hold the forearm in a horizontal position such that the small angle between the long axis of the upper arm and the forearm ranges from 15°-75°. Your task is to perform biostatics analysis to determine if any of these loads causes tendon tension to exceed the value advised by the injury specialist. From this analysis, you will prepare a report for submission to the employer.

Theoretical System Parameters for Biostatics Analysis

Fig. 1 shows a pictorial diagram of the extended forearm holding a load in the supinated hand.

2398_Pictorial diagram of the extended forearm handling a variable mass.jpg
Fig. 1: Pictorial diagram of the extended forearm handling a variable mass.

Assume that the axis of rotation of the elbow is fixed at point O and the attachment point of the distal biceps tendon is located at point A, a = 5.7 cm from O. The mass of the entire forearm including hand is mB = 1.66 kg and its center of gravity is located at point B, b = 21.0 cm from O. Define the load in the hand as mC; its center of gravity is located at point C, c = 40.6 cm from O. Define FM as the biceps tendon tension. Assume that the line of action of FM is parallel to the long axis of the upper arm throughout the specified range of motion.

Therefore, define θ as the angle FM makes with the forearm; i.e., with respect to horizontal.

Report Guidelines

1) Prepare an electronically-generated free-body diagram of the system utilizing the parameters outlined above. You may use shapes in MS Word or the drawing program of your choice. Include all dimensional information and a coordinate system.

2) Derive an expression for the magnitude FM in terms of θ and mC. Hint: you only need one rotational equilibrium equation to do this.

3) Compute FM for each of seven masses placed in the hand [mC = 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, and 6.0 kg] at each of seven angles of distal biceps tendon tension [θ = 15, 25, 35, 45, 55, 65, and 75°]. Prepare a table with these 49 values of distal biceps tendon tension, with θ placed along the x-axis (columns) and mC placed along the y-axis (rows). Label and caption this table. Highlight values that exceed the limit advised by the injury specialist in a suitable color.

4) Generate a graph with seven smoothed-line scatter plots (including data points) showing FM (y) vs. θ (x) for each of the seven masses using Excel or MatLab. Draw a heavy line on the graph in a suitable color indicating the tension limit advised by the specialist. Likewise, generate a similar graph showing FM (y) vs. mc (x) for each of the seven angles and a line indicating the advised tension limit. Label and caption both graphs.

5) Prepare a formal report in MS Word and submit a .docx file with the following sections:

• Cover Page

o name of the university and department
o title of the report
o submitted by: (your name)
o submitted to: (Dr. Joe Tritschler)
o date of submission

• Introduction and Purpose

o You may paraphrase the description of the problem in this assignment, but don't simply copy and paste it.

• Data and Results

o Include all diagrams, derivations, equations, tables, and charts.

• Discussion

o Discuss the figures in the table and charts and address the following questions:

- What happens to the theoretical magnitude of distal biceps tendon tension as the arm becomes fully extended; i.e., θ approaches zero degrees?

- What does this suggest about the limitations of our analysis?

• Conclusions and Recommendations

o Should the injured employee undergo on-the-job rehabilitation?
o Specify design parameters for a rehabilitation algorithm based on your computations.

Reference no: EM131261817

Questions Cloud

Identify main points and sections of the research project : Provide an Introduction, Body, and Conclusion. Identify the main points and sections of the Research Project. Identify the sub-topics and details consistent with the main points and sections. Present information in an organized and logical manner.

Keep the product the same but alter the promotion : Describe at least three situations where an American company might want to keep the product the same but alter the promotion.

Which equations would need to be modified : Suppose the aircraft is in steady flight and the decrease in the weight of the aircraft as fuel is burned is taken into account in the analysis. What modifications would need to be made to the development?

How social factors as gender racial and ethnic background : Summarize three (3) key aspects of the juvenile case study that you selected. Highlight at least three (3) factors that you believe are important for one to understand the origins of the juvenile's delinquent behavior.

Prepare electronically-generated free-body diagram of system : Prepare an electronically-generated free-body diagram of the system utilizing the parameters outlined above. You may use shapes in MS Word or the drawing program of your choice.

Techniques that help make strategic planning effective : Identify several techniques that help make strategic planning effective. - What techniques can make your school enrollment marketing plan more effective?

What is motivational on the job-either in the business world : Search the Internet for a recent article on what is motivational on the job-either in the business world or in law enforcement. In a one page paper, outline your findings and include the full source of the article.

What will be the number of memory bits/chip in the year 2020 : The change in memory density with time can be described by B = 19.97 × 100.1977(Year-1960). If a straight-line projection is made using this equation, what will be the number of memory bits/chip in the year 2020?

Can dan be convicted of some form of criminal homicide : Assume instead that the truck strikes missy first. While she is laying near death in the middle of the street, Danny lives up to his champion reputation and shoots Missy, killing her instantly. It is clear that Missy would have died shortly from t..

User Account

All Pages