Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Prepare a ladder diagram for the process described in given Example and given Figure. Assume a logic off-delay 5-minute timer (i.e., goes true when enabled and stays true for 5 min). Assume a NO start push button and an NC stop push button
Example Construct a state variable description of the process shown in given Figure. The timer output (TU) is initially low when its input (TM) is low. When TM is taken high the output stays low for five minutes and then goes high. It resets to low when TM is taken low. All level sensors become true when the level is reached. The process sequence is:
1. Fill the tank to level A (LA) from valve A (VA)
2. Fill the tank to level B (LB) from valve B (VB)
3. Start the timer (TM), stir (S), and heater (H)
4. When five minutes are up take stir (S) and heater (H) off.
For a unity feedback control system, the forward path transfer function is: G(s) = 20/(s^2 + 14s +50) a. Determine the steady-state error for a unit step input. b. Find the steady-state error for a unit ramp input using the Final Value Theorem.
The voltages at the generators buses are maintained at a magnitude of 1.0pu. The generator one (G1) is connected to bus 1. The generator two (G2) is connected to bus 2. The bus angle at bus 2 is taken as reference and is 00.
Design the circuit such that IDQ = 0.25 mA and VD = -2 V. The nominal transistor parameters are VTP = -1.2 V, K'p, = 35 μA/V2 and viL = 15. Sketch the load line and plot the Q-point.
Describe the operation of the series RC circuit. The discussion must address phase angle relationships of current and voltage. The answer must include the effect of source frequency on the voltage drops across the resistor and the capacitor at ver..
For the op-amp in the voltage follower circuit in Figure P14.14, the open loop parameters are AO L = 5 × 103, Ri = 10 k, and Ro = 1 k.
The mass spectrometer measurement section is a region of uniform magnetic field B= ˆxBms for z > 0. Ions enter the magnetic field (which exists for z > 0) at the origin with a known velocity +ˆz vz.
Derive a system diagram for a frequency-modulated transmitter and explain the function of each stage and detect and reproduce (demodulate) the message signal. Measure the frequency of the detected signal and compare that with the frequency of the m..
Energy per unit length. A line of charge with line charge density PI is surrounded by a dielectric layer as shown in Figure 4.80. The permittivity of the layer is ε. Calculate the energy per unit length stored in the cylinder (a ≤ r ≤b.
A priority decimal-to-BCD encoder has active-LOW inputs andoutputs. If there are LOWs only on decimal inputs 2, 5, and 8, what BCD code appears on the outputs
Complete paraphrase all report and changing words. - Develop and use a procedure to determine (identify) the equivalent circuit for an unknown linear, passive circuit.
Design an analog computer circuit (using minimum resistor values of 10 k ohms ) to obtain the summing (adder) function. Vo = -v1 -v2 +v3
Design a circuit that has 4 inputs, WXYZ, and two outputs, f and g, where W is the most and Z is the least significant bit. The output f is asserted whenever the two-bit number WX is greater than the two-bit number YZ.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd