Find the force required of the air cylinder

Assignment Help Mechanical Engineering
Reference no: EM131392717

Figure P11-11 shows a paper roll off-loading station. The paper rolls have a 0.9-m OD, 0.22-m ID, are 3.23 m long, and have a density of 984 kg/m3. The forks that support the roll are 1.2 m long. The motion is slow so inertial loading can be neglected. Find the force required of the air cylinder to rotate the roll through 90°

2324_8067b227-7573-4055-9f88-ef756a803a77.png

Reference no: EM131392717

Questions Cloud

How do you conceptualize the contribution : The nature/nurture debate has been in existence for years, and now we know that both contribute to mental health issues. How do you conceptualize the contribution of both, and do you believe one has more influence than the other?
How culture is a factor in determining the expression : Provide a brief overview of how culture is a factor in determining the expression of psychopathology.Examine the causes of psychopathology using one of the following major psychological perspectives: Psychodynamic, Behavioral, or Cognitive-Behavio..
Design this device and its mounting hardware : Design this device and its mounting hardware to the truck bed minimizing the dynamic forces and driving torque.
Construct a narrative statement outline of event sequence : Construct a narrative statement outline of the event sequence for the system shown in gien Figure. The objective is to fill bottles moving on a conveyor.
Find the force required of the air cylinder : The motion is slow so inertial loading can be neglected. Find the force required of the air cylinder to rotate the roll through 90°
Develop a jeopardy game presentation : You only need 5 slides 100-500 on Holistic approach to higher learning; u will better understand when u open the below powerpoint how everything is set up, but dont forget each answer needs to be better explained in the note section of the powerpo..
Prepare a ladder diagram for the process : Prepare a ladder diagram for the process described in given Example and given Figure. Assume a logic off-delay 5-minute timer.
Write a book review of the new christian counselor : Many have poor self-management skills, often neglecting to take medications, show up for work, etc. Some cannot even adequately complete activities of daily living (ADL's). Legal problems are often part of your challenges as is homelessness. Your ..
Find the pin forces and slider side loads : Find the pin forces, slider side loads, and driving torque over one revolution for a cutting force of 250 N in the forward direction and 50 N during the return stroke.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd