Plot frequency-gain dependence plot using plotting software

Assignment Help Other Engineering
Reference no: EM131410533

Experiment: Non-Inverting Op-Amp frequency response

Objective: To understand and gain and frequency relationship in non-inverting amplifier configuration.

Components and instruments needed:

• Resistors: one 1 k?, one 150k?
• Capacitors: two 1.0 µF
• Op-amp: one LM741C
• DC power supply
• Function generator
• Multimeter

1267_Figure.jpg
Figure 1

Procedure:

1. The schematic for the non-inverting amplifier is shown in the figure 2.

2. Measure and record the resistor values in table 1. Input resistance Ri = 1 k?, feedback resistor Rf = 150k?.

Table 1:

Resistor

Listed value

Measured value

Ri

1 k?

983.20 ?

Rf

150 k?

151.68 k?

3. Connect the circuit shown in figure 2.

4. Apply a 50 mVrms, 1 kHz (no offset) sine wave input to the non-inverting as shown in the figure.

5. Using the multimeter measure and record Vin and Vout in table 2. Note that the multimeter gives you RMS values only.

6. Increase the frequency from 1 kHz to 10 kHz at 2.5 kHz steps and repeat the step 5 (i.e., measure Vin and Vout) for each frequency.

7. Plot the frequency-gain dependence plot using a plotting software (such as excel) and include it in your lab report.

Table 2:

Source frequency

Vin

Vout

Acl(NI)

1 kHz

50.36 mV

7.694 V

152.78

2.5 kHz

50.36 mV

7.220 V

143.37

5 kHz

50.36 mV

6 V

119.14

7.5 kHz

50.36 mV

4.833 V

95.97

10 kHz

50.36 mV

3.94 V

78.24

2025_Non-Inverting Amplifier.jpg
Figure 2

Report:

Write a report that summarizes this experiment. Your report brief must include:

a) Cover sheet.

b) Objective - a short paragraph stating what the experiment is about.

c) Procedure - a description of the process of conducting the experiment. It should not be a step-by-step account, but rather an overview of what was done.

d) Discussion - a complete discussion of the results of the experiment and the principals involved. Include the outputs and also the screen captures as needed to support the statements made in this section. Relegate extensive lists of raw data and detailed computations to an appendix as appropriate.

e) Conclusion - a summary of what you have learned from the experiment.

Reference no: EM131410533

Questions Cloud

Should companies involve their marketing channels in design : Should companies involve their marketing channels in the design of their customer communication programs? What are the advantages and disadvantages of doing so?
Planet gravity acceleration : 1. Use reasoning to determine if one of the following objects in each of these pairs has a greater value for the magnitude of its momentum than the other. ( no calculations should be required.)
Obtain a positive ion and a negative ion : 1. How do we obtain a positive ion and a negative ion? Give an example. 2. Why do we use more AC versus DC?
Compute the proceeds from each of the three notes : An eight-year note with an annual stated rate of 8 percent and a face value of $35,000.Interest is paid annually on December 31. The effective interest rate is 10 percent.
Plot frequency-gain dependence plot using plotting software : Write a report that summarizes this experiment. Your report brief must include: Plot the frequency-gain dependence plot using a plotting software (such as excel) and include it in your lab report.
Minimum acceleration be to catch the parachutist : What must her minimum acceleration be to catch the parachutist right at the ground?
What is unique about the google culture : What is unique about the GOOGLE culture - Will GOOGLE be able to sustain this type of culture and what might be some aspects of the DARK SIDE of Google?
What are the likely issues you will encounter : Your company is organized under a traditional tall structure that is departmentalized by function. Using your knowledge about culture clash (see page 108), what are the likely issues you will encounter if these two organizations are merged?
Air downstream of the reflected shock : What is the Mach number of the reflected shock that travels back toward the piston? What are the static pressure and temperature of the air downstream of the reflected shock?

Reviews

Write a Review

Other Engineering Questions & Answers

  The machine will consist of a base or frame

The machine will consist of a base or frame, a rotary actuator (to obtain the 90 degree desired rotation about the x-axis), a linear actuator that will move plates back and forth to obtain the 180 degree axis rotation about the y-axis, and a PLC/HMI ..

  What airspace model would you advocate and why

What minimum CNS systems would you recommend - What level of CNS would you recommend considering safety, cost and insurance concerns? If you could influence the regulator, what airspace model would you advocate and why?

  Describe and analyse the current network

Design the network you would recommend and how it would be configured. Remember the goal of building a new network is that it will support the schools needs for the next five years - Draw compressive physical network(s) diagram that shows how you c..

  What is the power dissipated in the chip

If the inverter is operated from a 1.8-V power supply, find the energy needed to charge and discharge the load capacitance. If the IC chip has 2 million of these inverters operating at an average switching frequency of 1 GHz, what is the power dis..

  Compute the rms and maximum peak instantaneous value

Compute the RMS and maximum peak instantaneous value of the fault current, for a balanced three-phase fault.

  Completment of the triangle

From Girard's theorem for a triangle, deduce Girard's theorem for the completment of the triangle.

  It is important to include who worked on what questions on

working with your group detail the steps needed to monitor administrate and secure the network in regard to online

  Calculate what is the minimum discharge voltage with load

ECE2795 Homework Assignment. Consider that you are using 20 Maxwell Boostcap BCAP2000 connected in series to provide energy to a 1 ohm resistive load. Please, find v(t) and calculate what is the minimum discharge voltage with this load

  What are the key technological issues behind the technique

How does this process / technique / etc. improve on what had been done in the past - what are the key technological issues behind the technique?

  Matlab and show the frequency matches in numerical

The cart has been pushed 1 m and then released where the mass of the cart is 10 kg and spring constant k=500 N/m. 1) Find the acceleration.

  Heat treatment of high tensile carbon steel

Explain why tempering cycle is essentially required in the heat treatment of high tensile carbon steel and what are the consequences if tempering cycle is not carried out?

  Dawes road and jeff hamilton road intersection redesign

Dawes Road and Jeff Hamilton Road Intersection Redesign. The Mobile County and Alabama Department of Transportation desire a redesign of the intersection of Jeff Hamilton Road and Dawes Road due to safety issues and poor level of service.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd