User Account

All Pages

Mouse trap car-find force of the spring and find friction

Assignment Help Mechanical Engineering
Reference no: EM13703078

A mouse trap car the length of the car is 41.5cmm and width of the car is 9 cm Length of Cirrus is 32 cm, the Length of the rope that connected from the cirrus till the from wheels is 56 cm, the Height of the vehicle from the ground is 3 cm, The length of the spindle is 10 cm. Find the the normal force and find the force of the spring and find friction and. ( the mouse trap car start from rest so v1=0 find v2 when the car stop at 6m from The starting point.

Reference no: EM13703078

Questions Cloud

A multiple disc has radial width of the friction material : A multiple disc has radial width of the friction material 1/5th of the maximum radius. The coefficient of friction is 0.25. Find the total number of discs required to transmit 60 kW at 3000 r.p.m. The maximum diameter of the clutch is 250 mm and the ..
Determine the instantaneous heat input : A power plant produces 1000 MW of electricity and uses residential oil as the fuel. The oil has a heating value, the maximum energy liberated in combustion, of 43 000 kJ/kg. The overall efficiency of the power plant is 52%.
Magnitudes of velocities immediately after they collide : The kinetic coefficients of friction between the 5-kg crates A and B and the inclined surface are 0.1 and 0.4, respectively. The coefficient of restitution between the crates is e = 0.8. If the crates are released from rest in the positions shown, wh..
Ball bearings uses oil whose viscosity ranges : A pump fitted with 50mm bore ball bearings uses oil whose viscosity ranges from 100cSt at cold pump start-up to 7.5Cst when running at maximum speed and load. If these viscosities are the safe limits for the oil, specify the maximum start-up speed an..
Mouse trap car-find force of the spring and find friction : A mouse trap car the length of the car is 41.5cmm and width of the car is 9 cm Length of Cirrus is 32 cm, the Length of the rope that connected from the cirrus till the from wheels is 56 cm, the Height of the vehicle from the ground is 3 cm, The leng..
Hub is shrink-fit onto a solid carbon steel shaft : A brittle cast iron (E = 15 Msi, ? = 0.2, Sut = 30 ksi, Suc = 100 ksi) hub is shrink-fit onto a solid carbon steel shaft. The hub has initial inner and outer diameters of 3.000 and 6.000 inches respectively. What is the largest diameter the steel sha..
Will the same magnus force be created to power the boat : A freely (zero friction) rotating cylinder (mounted on a vertical axis) is placed on a model boat instead of a sail. The Magnus force that is created is used to power the boat. A fan is mounted on the boat to provide airflow over the cylinder.
Determine the unknown viscosity : You are given a small dc motor and fully-charged D battery. How would you use that motor to help determine the unknown viscosity of an oiled sample? You can acquire any other materials needed. What other materials would you need and what procedure wo..
What force is the drill bit placing on the surface : Suppose a 24V drill has a current drawn from it that measures 5 amps. The drill bit is 2 inches in diameter. What force is the drill bit placing on the surface if the speed is 25 rpm? Assume the drill has an efficiency of 90%

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Consider a model of a bone with a cemented prosthesis where

consider a model of a bone with a cemented prosthesis where the outside radius of the bone is ro the radius of the

  Determine a temperature quality and the volume in m3 of the

20 kg of water at 200 kpa with a quality 25 is heated under a constant volume process until its pressure reaches 400

  The remaining wet steam exits the turbine at 115 kpa with a

consider a steam turbine in which steam enters at 10.45 mpa and 780k with a flow rate of 38.739 kgs. a portion of the

  A four cylinder 24 liter engine operates on a four stroke

a four cylinder 2.4 liter engine operates on a four stroke cycle at 3200 rpm. the compression ration is 9.41 the

  If the crate starts from rest and achieves a speed of 10 ms

the 50 kg crate is pulled by the constant force p. if the crate starts from rest and achieves a speed of 10 ms in 5s

  Treating the system as a particle assuming that the contact

a railcar with an overall mass of 75000 kg traveling with a velocity vi is approaching a barrier equipped with a bumper

  The upper half of the container holds steam of density

a transparent rigid sealed container has a volume of 10m3. the upper half of the container holds steam of density 5kgm3

  Determine the steady state irreversibility rate of each

the surface temperature of a 100 w incandescent lightbulb is 60.0degc. the surface temperature of a 20.0 w fluorescent

  A vessel contains 2 litres of gas at a pressure of 300kpa

a vessel contains 2 litres of gas at a pressure of 300kpa and a temperature of 27 degrees c. 3 litres of gas at the

  Assuming that xe behaves like an ideal gas with a specific

two m3 of xenonxe are contained in a closed rigid tank at 70 degree c and 2 bar. the tank is heated to a pressure of 10

  The net force applied by the belt on the pulley is 2000 n

the driveshaft of a buildings air-handling fan is turned at 300 rpm by a belt running on a 0.3- m-diameter pulley. the

  Determine the magnitude of its total accleration

determine the magnitude of its total accleration when (a) t=0 and (b) t=2 Whats the solution.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd