Money was made in interest over the initial investment

Assignment Help Mechanical Engineering
Reference no: EM13705881

If a single deposit of $25000 is invested at 1.75% yearly interest, what equal year-end withdrawals can be made each year for 10 years, leaving nothing in the fund after the 10th withdrawal? How much money was made in interest over the initial investment?

Reference no: EM13705881

Questions Cloud

Air is heated in an adiabatic piston cylinder device : Air is heated in an adiabatic piston cylinder device at a constant pressure of 100 kPa. The initial specific volume of air is 1 m3/kg. If the volume of the cylinder is increased by 50% in this process, determine the specific entropy change of air in ..
Required per unit mass for the isothermal compression : Find the theoretical work required per unit mass for the isothermal compression of 800 m3 air from 100KPa to 900 KPa in closed system.
Work required for compression and final pressure of gas : A gas is contained in a piston of 5 m3 at 100 KPa. Then the gas is compressed till its volume is reduced to 2.5 m3. If there was no exchange of heat from the system during the compression process, calculate the work required for the compression and t..
Determine the work for the process with the value : A gas in a piston-cylinder assembly undergoes an expansion process for which the relationship between pressure and volume is given by pV^n = constant. The initial pressure is 4.25 bar, the initial volume is 0.25 m^3 and the final volume is 0.55 m^3.
Money was made in interest over the initial investment : If a single deposit of $25000 is invested at 1.75% yearly interest, what equal year-end withdrawals can be made each year for 10 years, leaving nothing in the fund after the 10th withdrawal? How much money was made in interest over the initial invest..
What is the new gage pressure : The gage pressure in an automobile tire when measured during winter at 32 o F was 32 psig. The same tire was used during the summer when the temperature rose to 112 o F. If we assume that the volume of the tire did not change, and no air leaked out b..
Experiences a constant horizontal acceleration : An object of mass 10 kg, initially at rest, experiences a constant horizontal acceleration of 4 m/s^2 due to the action of a resultant force applied for 20 s. Determine the total amount of energy transfer by work in kJ.
Determine the amount of jet fuel consumed during take off : A jumbo jet with a mass of 5 million kg requires a speed of 175 mph for takeoff. Assuming an overall efficiency of 20% (from heat release to kinetic energy of the aircraft), determine the amount of jet fuel (heating value: 44 MJ/kg) consumed during t..
Equation of motion for the initial conditions : Find the response of systems governed by the following equation of motion for the initial conditions x(0)=1, xdot(0)=-1:

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the cycle thermal efficiency and the net work per

consider an ideal steam combined reheat and regenerative cycle in which steam enters the high-pressure turbine at 500

  What would be the velocity of the sound in the tube for

estimate in mm your uncertinity in locating the position of a resonance level. are the resonances sharp located at a

  Consider the isothermal expansion of 450 mol of an ideal

consider the isothermal expansion of 4.50 mol of an ideal gas at 450 k from an initial pressure of 12.0 bar to a final

  Determine the maximum axial compressive force

A short 60-mm-diameter circular bar is made of a material for which the maximum safe compressive stress is 80 MPa and the maximum safe shearing stress is 30 MPa. Determine the maximum axial compressive force that can be safely applied.

  Find the desired radius and mass of the absorber

Find the desired radius and mass of the absorber if the absorber is to not exceed an angular deflection amplitude of 30 degrees when the engine is running at 750 rpm.

  Let the coefficient of friction between the car and the

highways are banked to increase the maximum safe speed at which cars can negotiate a turn. assume a road with radius of

  Determine the magnitude of forces t

the boat is to be pulled onto shore using two ropes. If the resultant force is to be 1000 N, directed along the keel aa , determine the magnitude of forces T, P acting in each rope at the angle teta of P so that the magnitude of P is minimum. T ac..

  The upper surface of a 50-cm-thick solid plate k237 wmk is

the upper surface of a 50-cm-thick solid plate k237 wmk is being cooled by water with temperature of 20 degrees

  What are the sources of error in your system how can you

design an experiment complete with instrumentation to determine the specific heats of a liquid using a resistance

  The mix leaves the chamber at 200kpa and 70 dgree clecius

water at 200 kpa and 10 degree celcius enters a mixing chamber at a rate of 150 kgmin where it is mixed steadily with

  Determine the microstructure for eutectoid steel that has

determine the microstructure for eutectoid steel that has undergone the following heat treatment. for each heat

  Determine the maximum possible volume flow rate for this

a 5 kw pump operating at steady state receives liquid water at 100 kpa 15 c and delivers it to a point 6 m above the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd