User Account

All Pages

Maximum stress in the ring

Assignment Help Electrical Engineering
Reference no: EM13864909

A steel ring of 250mm diameter has a width of 50mm nada radial thickness of 5mm. It is split to leave a narrow gap 5mm wide normal to the plane of the ring. Assuming the radial thickness to be small compared with the radius of ring curvature, find the tangential force that must be applied to the edges of the gap to just close it. What would be the maximum stress in the ring under the action of this force? E=200GPa

Reference no: EM13864909

Questions Cloud

Adjustment for any underapplied or overapplied overhead : Aerobars Inc. uses a job-order costing in which any under applied or over applied overhead is closed out to cost of goods sold at the end of the month. The company's cost of goods manufactured for March was $167,000; Determine the cost of goods sold ..
A very old man with enormous wings : Read "A Very Old Man with Enormous Wings" by Gabriel García Márquez (in the course textbook and attached below). Reflect and respond to the story in a 3- to 4-page reader-response essay. Remember that reader-response essays are less formal than other..
Bending moments and vertical reactions : Determine the bending moments and vertical reactions at the supports and sketch the BM and SF diagrams.
Any paid-in capital from treasury stock-journal entry : A company reissued at $20 per share 100 shares of treasury stock that it had previously acquired for $26 per share and there was not any Paid-in Capital from Treasury Stock. Prepare the journal entry.
Maximum stress in the ring : What would be the maximum stress in the ring under the action of this force? E=200GPa
An image at least one slide must contain animation : Create a PowerPoinf. presentation that introduces you to the audience. You may want to include information about your background, hobbies, major, and what you plan to do after graduation. Your presentation must be between six and ten slides. Your pre..
Zero-interest-bearing note : Edson Corp. signed a three-month, zero-interest-bearing note on November 1, 2011 for the purchase of $150,000 of inventory. The face value of the note was $153,000. Edson used a “Discount on Note Payable” account to initially record the note and the ..
Determine the magnitude of the force on the plate : Water discharges at a rate of 5L/s through a nozzle. The jet, 25 mm in diameter, strikes a flat plate held perpendicular to its line of flow. Determine the magnitude of the force on the plate
Attorney has indicated that loss is probable : Cameron Inc. is a defendant in a lawsuit. The company’s attorney has indicated that a loss is probable. The amount of loss can be estimated to be within a range of $5 million to $15 million. How should Cameron handle this situation on the books? Prep..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What gauge of wire would use if needed to limit power loss

You plan to integrate a sensor that operates at 24 VDC and 2A At distance of 100 feet from your controller under normal conditions. What gauge (AWG) of wire would you use if you needed to limit your power loss to 10%

  Determine what is the total power drawn by the load

Two watt-meters connected to read the total power drawn by a balanced three-phase load. If the two readings are 1000 W and -1000 W, what is the total power drawn by the load

  What is the utility of a linear model of patient care

What is the utility of a linear model of patient care as the basis for a decision-support system? What are two primary limitations? Discuss two challenges that a nonlinear model poses for representing and supporting the care process in an infor..

  How many turns should be would on the secondary coil

A nickel-iron ring withcross-sectional area 0.85cm2 is expected to be driven to itssatur-ation magnetization of 1.1T in a ?eld of 800 A/m. The ?ux density will be measured by an electronic ?ux integrator with input resistance of 1kOhm

  Find the swr on the line and the reflection coefficient

A lossless transmission line of electrical length l = 0.3? is terminated with a complex load impedance . Find the reflection coefficient at the load, the SWR on the line, the reflection coefficient at the input of the line

  Design a single-ended amplifier with a low frequency gain

The available circuit components are NMOS transistor, PMOS transistor, resistors, capacitors and inductors. Ideal sources can only be used to generate the supply voltage VDD & GND.

  What is the frequency of the voltage in hertz

A sinusoidal voltage has maximum amplitude of 90 V. The voltage passes through one complete cycle in 64 ms. What is the frequency of the voltage in hertz

  In mel brooks robin hood mens in tightsbullexplain how

in mel brooks robin hood mens in tights.bullexplain how the artists utilize lighting in the scene. how does the

  Express the vector as a linear combination of the elements

A canonical base for H7 is {(0000001), (0000010), (0000100), (0001000), (0010000), (0100000), (1000000)}. Express the vector (1010111) as a linear combination of the elements of the canonical base.

  Describe performance differences between an am and fm system

Describe the performance differences between an AM and FM system. Be sure toinclude parameters suchas: Power efficiency, spectral efficiency,noise immunity,and performance.

  Design the circuit to create pulse using j-k flip flops

moore sequential circuit has one input and one output, that creates a pulse when ever its input signal goes from 1 to 0 after this pulse a new pulse will not be given unless the input signal is again returned to 1 and then tranistion back to 0.

  Find the charge delivered to device between time interval

The current entering the positive terminal of a device is i(t)= 6e^-2t mA and the voltage across the device is v(t)= 10di/dtV. ( a) Find the charge delivered to the device between t=0 and t=2 s.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd