Maximum normal stress theory-maximum shear theory

Assignment Help Mechanical Engineering
Reference no: EM13707426

A torsion bar is used as a suspension element for a vehicle. The bar has a diameter of 20mm. It is subjected to a torsional moment of 450Nm and an axial tensile force of 36.0kN. Draw a stress element on the surface of the bar and then draw the Mohr's circle for the element, find the principal stresses, the maximum shear stress, and also the principal and shear plane angles. What are the minimum yield strength and ultimate tensile strength required to satisfy following failure theories (assume that design factor, F=2): 1.Maximum Normal stress Theory 2. Maximum Shear Theory 3. Distortion Energy Theory.

Reference no: EM13707426

Questions Cloud

A rigid tank with a volume : A rigid tank with a volume of 1.8 m3 contains 15 kg of saturated liquid-vapor mixture of water at 2 bar. Now the water is slowly heated. Determine the temperature at which the liquid in the tank is completely vaporized. Show the process on a T-v diag..
Develop your knowledge and skills in the areas : Develop your knowledge and skills in the areas - Modbury Triangle Shopping Centre v Anzil and roads and Traffic Authority v Dederer
Modelling the air as ideal gas with constant specific heats : Air is contained in a piston-cylinder assembly, initially at 40 psia and 600 R. The air expands in a polytropic process with n = k = 1.4 until the volume is doubled. Modelling the air as an ideal gas with constant specific heats,
Determine the final temperature and pressure : A piston-cylinder assembly contains CO2. The CO2 expands with PV1.5=constant where the initial state is 200 degrees F and 40 lbf/in^2, to a final state where the volume doubles. Determine the final temperature, pressure, work and heat transferred
Maximum normal stress theory-maximum shear theory : A torsion bar is used as a suspension element for a vehicle. The bar has a diameter of 20mm. It is subjected to a torsional moment of 450Nm and an axial tensile force of 36.0kN. Draw a stress element on the surface of the bar and then draw the Mohr's..
Geoffrey is building an electronic circuit on a breadboard : Geoffrey is building an electronic circuit on a breadboard. He needs to supply his circuit with a 1500 ohm resistance. But he does not have any 1500 ohm resistors on hand. All he has is a box of 1000 ohm resistors.
Determine the maximum shear stress at the point : The stresses at a point in plane stress on a sheet metal roof were found to be sigma_xx = 10 ksi (C), sigma_yy = 20 ksi (C) and Tau_xy = 30 ksi using matrix methods a) determine the normal and shear stresses on a plane passing through the point that ..
Determine the design thrust for a throat area : A rocket nozzle has a chamber pressure of 20 Bar (2 MPa) and a chamber temperature of 2750 K. The rocket is designed to operate isentropically at 12,500 m altitude. Note that the pressure at 12,500 m can be estimated using this equation P/P0 = exp [-..
Determine internal pressure required to initiate yielding : A thin-walled cylindrical pressure vessel is capped at the end and is subjected to an internal pressure (p). The inside diameter of the vessel is 6 ft and the wall thickness is 1.5 inch. The vessel is made of steel with tensile yield strength and com..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd