Matlab program-average of digits of part using for loops

Assignment Help Mechanical Engineering
Reference no: EM13703811

Write the MATLAB program to find the maximum, minimum and average of the digits of part (a) using for loops. Execute the program and list the output. Note that you are not allowed to use MATLAB commands max(x), min(x) and mean(x), except for checking your results.

Reference no: EM13703811

Questions Cloud

What is torque required to stop it from spinning : A Cylinder of mass 20 lbs, radius 5in and height 10in is spinning about its axis of symmetry (central axis) at 200 rpms. What is torque required to stop it from spinning
Matrix with digits of the input number as diagonal elements : Write the MATLAB program which takes 8 digits number as input, then creates an 8x8 matrix with digits of the input number as diagonal elements and zeroes elsewhere using for loops. Then, execute the program using your student ID as input.
Determine the actual exit temperature for the compressor : A given mass flow rate (.17 kg/min) of an ideal gas flows through an adiabatic compressor operating at steady state. The compressor has an adiabatic efficiency of N(%) = 87.5. The gas has a molecular weight of MW = 28.5 (kg/kmol) and a specific heat ..
Estimate extra cost per year due to increased use of blades : Current airbag regulations specify that they must only pass a test designed to protect a 175 pound male who is not wearing a seatbelt. There is currently a discussion of lowering the explosive force by 30%, so that smaller-sized people (including wom..
Matlab program-average of digits of part using for loops : Write the MATLAB program to find the maximum, minimum and average of the digits of part (a) using for loops. Execute the program and list the output. Note that you are not allowed to use MATLAB commands max(x), min(x) and mean(x), except for checking..
What specific materials are used for solar cells : What specific materials are used for solar cells? What specific properties these materials process in order for the solar cells to the function properly?
Double-pipe heat exchanger : Double-pipe heat exchanger. This type of heat exchanger is composed of concentric pipes, with hot water flowing in the inner pipe while cold water flows in the annulus between the inner pipe wall and outer pipe wall.
Mass of oxygen gas in a container with a volume : What is the mass of oxygen gas in a container with a volume of 25 ft3, at a pressure of 14.7 psia and a temperature of 75oF?
Determine the radial wall thickness-speed in rpm : A flat disk of outer radius b-125mm and inner radius a=25mm is shrink-fitted onto a shaft of radius 25.05mm. Both members are made of steel with E=200Gpa, v=0.3, and p=7.8 KN.s2/m4. Determine (a) the speed in rpm at which the interface pressure becom..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The acceleration of a particle as it moves along a straight

the acceleration of a particle as it moves along a straight line is given by a 2t-1ms2 where t is in seconds. if s 1m

  Compute the volumetric flow rate issuing out of the pipe

A large oil reservoir has a pipe of 4 in ID and 7000-ft length connected to it. The free surface of oil (kinematic viscosity = 1 x 10^4 ft2/s) in reservoir is 10 ft above the centerline of the pipe and can be assumed to remain at this fixed elevation..

  What force must be applied to the plunger

the pressure in the vein is known as 1850 Pa. what force must be applied to the plunger, so that 1.5 x 10^-6 m^3 of solution can be injected in 5.0 s?

  Assume the brake pads are 1 lbmin with a heat capacity of

a car with mass 3250 lbm is driven at 60 mih when the brakes are applied to quickly decrease its speed to 20 mih.

  What is the gage pressure of the air inside the piston what

consider the arrangement described in problem 1. a cable attached to the 100 lbm piston exerts a 200 lb force upward on

  The channel is rectangular 20 m wide with a bedslope of

a in a short section of a channel carrying a steady discharge of 36 m3s the depth is seen to increase from 1.6 m to

  The overall heat transfer coefficient is 280 w m2middot

water at the rate of 230 kgh at 35degc is available for use as a coolant in a double-pipe heat exchanger whose total

  Use the perfomance characteristics of the marine propeller

total power required to overcome viscous resistance and wave drag is 11.4 mw. use the perfomance characteristics of the

  Determine a the temperature at the turbine inlet in degrees

a steam turbine at steady state is operated at part load by throttling the steam to a lower pressure before it enters

  Water is pumped from a lower reservoir to a higher

water is pumped from a lower reservoir to a higher reservoir by a pump that provides 15 kw of shaft power. the free

  How far up the slope will the mass move before coming to

a spring 75 nm has an equilibrium length of 1.00 m. the spring is compressed to a length of 0.50m and a mass of 2.1kg

  A hydraulic jump forms in a horizontal trapezoidal channel

a hydraulic jump forms in a horizontal trapezoidal channel. the base width is 4m and the side slopes are 45 degrees.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd