Mass of oxygen gas in a container with a volume

Assignment Help Mechanical Engineering
Reference no: EM13703808

What is the mass of oxygen gas in a container with a volume of 25 ft3, at a pressure of 14.7 psia and a temperature of 75oF?

Reference no: EM13703808

Questions Cloud

Estimate extra cost per year due to increased use of blades : Current airbag regulations specify that they must only pass a test designed to protect a 175 pound male who is not wearing a seatbelt. There is currently a discussion of lowering the explosive force by 30%, so that smaller-sized people (including wom..
Matlab program-average of digits of part using for loops : Write the MATLAB program to find the maximum, minimum and average of the digits of part (a) using for loops. Execute the program and list the output. Note that you are not allowed to use MATLAB commands max(x), min(x) and mean(x), except for checking..
What specific materials are used for solar cells : What specific materials are used for solar cells? What specific properties these materials process in order for the solar cells to the function properly?
Double-pipe heat exchanger : Double-pipe heat exchanger. This type of heat exchanger is composed of concentric pipes, with hot water flowing in the inner pipe while cold water flows in the annulus between the inner pipe wall and outer pipe wall.
Mass of oxygen gas in a container with a volume : What is the mass of oxygen gas in a container with a volume of 25 ft3, at a pressure of 14.7 psia and a temperature of 75oF?
Determine the radial wall thickness-speed in rpm : A flat disk of outer radius b-125mm and inner radius a=25mm is shrink-fitted onto a shaft of radius 25.05mm. Both members are made of steel with E=200Gpa, v=0.3, and p=7.8 KN.s2/m4. Determine (a) the speed in rpm at which the interface pressure becom..
Temperature in the cylinder immediately after filling : As part of a super-critical extraction of coal, an initially evacuated cylinder is fed with steam from a line available at 20 mPa and 400 degrees C. What is the temperature in the cylinder immediately after filling? (Answer to problem is 454 degrees ..
Temperature of refrigerant at end of the heating process : A rigid tank is heated for 9 minutes with a 800W electrical heater. During this time 70kJ of energy is lost due to heat transfer to the environment. Find the temperature of the refrigerant at the end of the heating process.
Determine the rate of evaporation of water : Water is boiled at sea level (1 atm pressure) in a pan placed on top of a 2-kW electric burner that transfers 60% of the heat generated to the water. Determine the rate of evaporation of water in kg/s.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the temperature and pressure at the nozzle inlet

Helium gas enters a nozzle, whose isentropic efficiency is 95 percent with a low velocity, and it exits at 14.4 psia, 160 degrees F, and 940 ft/s. determine the temperature and pressure at the nozzle inlet.

  What is the density of liquid al-116si alloy at the melting

what is the density of solid aluminum at the melting temperature? what is the density of liquid aluminum at the melting

  Find the temperature at the interface

a. Find the temperature at the interface between the rod and sleeve and on the outer surface. b. What is the temperature at the center of the rod?

  Calculate a the power required by the compressor in kw b

he vapor compression heat pump operates at steady state using refrigerant 22 whose flow rate is 6kgmin. the heat pump

  Determine the velocity of molten metal flowing through

How do you determine the velocity of molten metal flowing through the base of the downsprue?

  A motorcycle is used to stunt show to go over a valley if

a. motorcycle is used to stunt show to go over a valley .if the initial speed at a is u ms then evaluate a ?the minimum

  The outer surface of the heater is exposed to a fluid with

a very thin electric heater is wrapped around the outer surface of a long cylindrical tube whose inner surface is

  A boat of length 50 m is designed to cruise at 30 mph and

a boat of length 50 m is designed to cruise at 30 mph and is to be tested in a tow tank with a model of length 0.5 m.

  The compressor has an isentro pi c efficiency of 95 assume

steam is expanded in an adiabatic turbine from 3 mpa and 400 c to 30 kpa. the turbine generates 4947kw of power when

  The top dead center is 14 percent of the bottom dead center

a six cylinder four stroke spark ignition engine operating on the ideal otto cycle takes in air at 1 atm and 18 oc and

  Positron has the same mass as an electron

When a positron and an electron meet, they are both annihilated into pure energy. Calculate how much energy (in MeV) is released in this reaction assuming that each particle is moving at 50% the speed of light. For this question use the classical def..

  A 90kw ideal power cycle takes in air at pressure 90kpa

a 90kw ideal power cycle takes in air at pressure 90kpa and discharges it at 945kpa. determine the rate of heat input

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd