List three types of vibration sensors

Assignment Help Other Engineering
Reference no: EM131103484

1) Circle the amplifier type that does not require voltage feedback for stability.

Voltage Follower, Current Feedback Amplifier, Comparator (SEE TI TEXT)

2) This is an equivalent circuit for a _______

1126_Circuit Diagram.jpg

3) As frequency goes up what happens to the CMMR

4) Draw a circuit which averages the incoming voltages to match this transfer function:

(E1+E2+E3+E4)/4 Hint TI Text

5) Given a bridge with two active elements R1 and R3 equal 300 ohms and R2 and R4 equal 300.9 ohms and the ref voltage is 10VDC followed by an AD621 set to 10X gain what is the reading at the output of the AD621.

578_Bridge Circuit Diagram.jpg

6) Draw a circuit labeling all components for a device to measure temperature and convert the temperature to a 0 to 10 VDC single for a 0 to 500 °C input using the AD594.

7) The reason that the AD594/AD595 had an onboard thermocouple was?

8) Given an RTD at 0 degrees C has a resistance of 103 ohms what is it at 375 degrees C if it is made of Tungsten.

9) Assume input is 1.125VAC draw this circuit to get this output

2114_Circuit Diagram1.jpg

10) Given the circuit below a.) what does this circuit do and b.) what could you use this circuit for?

1713_Circuit Diagram2.jpg

11) What types of industrial applications can an accelerometer be applied?

12) Draw a strain gauge circuit and its external components to attach to a conveyor mounted only at the ends to measure the load at the center of the conveyor. What type of testing would you need to do to establish a baseline and calibration curve for this sensor?

13) The circuit in question number 10 needs to be connected to a Labview network with both the input and output being tracked by Labview - select an interface to get this data into Labview (do not use the sensor daq) without the need for additional interface circuitry and justify your selection against cost, speed, and ability to have additional channels for other sensors. There are a tremendous number of manufacturers of DAQs, most interface to Labview.

14) What is an open collector input why is it used on some sensors.

15) List three types of vibration sensors and discuss how they operate.

16) What effect will temperature change have on a strain gauge mounted to steel and describe the multiple ways this can be compensated for by a user.

17) Using the ITS-90 Thermocouple Direct and Inverse Polynomials for a type J thermocouple calculate the voltage generated when the couple is placed in an 850°C environment.

18) Identify at least three strain gauge manufactures other than the manufacturer we used for our lab experiments.

Reference no: EM131103484

Questions Cloud

Consequences of non-compliance : Describe three employment laws and the consequences of non-compliance. Assess how an organization might structure their policies, practices or culture to ensure compliance.
Determine the output resistance of the circuit : Determine the output resistance of the circuit in Fig. 7.19(a) and compare the result with that in the above example. Assume M1 and M2 are in saturation.
What is the retailer''s effective cost of trade credit : A large retailer obtains merchandise under the credit terms of 1/15, net 45, but routinely takes 60 days to pay its bills. Given that the retailer is an important customer, suppliers allow the firm to stretch its credit terms. What is the retailer's ..
Possible response templates : Thank you for your post About Medicaid and Alabama. According to the United States Medicaid website  Alabama has adopted CMS guidelines for enrollment in Medicaid (Medicaid, 2016). In 2014, Alabama reported 17 out of 18, and 9 out of 10 healthcare..
List three types of vibration sensors : What is an open collector input why is it used on some sensors. List three types of vibration sensors and discuss how they operate. What effect will temperature change have on a strain gauge mounted to steel and describe the multiple ways this can b..
What is the nominal and effective cost of trade credit : What is the nominal and effective cost of trade credit under the credit terms of 3/15, net 30?
What do we refer the continuous movement of water : What do we refer the continuous movement of water from the ocean to the atmosphere to the land and back to the ocean
What is the company''s average accounts receivable : Medwig Corporation has a DSO of 17 days. The company averages $3,500 in credit sales each day what is the company's average accounts receivable?
What are the width and length of meq : What are the width and length of Meq?

Reviews

Write a Review

Other Engineering Questions & Answers

  Block diagram, system performance and responses

Questions based on Block Diagram, System Performance and Responses.

  Compute the allowable downward and upward load

These piles have been designed without the benefit of any onsite static load tests, dynamic tests or indicator piles, but a wave equation analysis has been performed. Using the Dennis and Olson method, compute the allowable downward and upward loa..

  Mass flow rate of isobutane

(a) The mass flow rate of isobutane in the binary cycle, (b) The net power outputs of both the flashing and the binary sections of the plant, and (c) The thermal efficiencies of the binary cycle and the combined plant.

  Capstone project meet all of the requirements of the scope

This essential step seeks to lay the foundation of determining the circuit/system's ability to meet the overall project objectives by answering the following questions:

  Write a report on environmental companies

Write a report on environmental companies

  Determine angular velocity of crate

Assuming that the impact is perfectly plastic, determine the angular velocity of the crate and the velocity of its mass center immediately after the cable becomestaut.

  Theoretical air during a combustion process

Ethylene (C2H4) is burned with 200 percent theoretical air during a combustion process. Assuming complete combustion and a total pressure of 14.5 psia, determine

  Find the number of strongly connected components

Find the number of strongly connected components in the graph and compute the in-degree centralization of the graph and compute the modularity score associated with that community structure in G.

  Provide a logic diagram that shows how a memr sometimes

provide a logic diagram that shows how a memr sometimes called oe signal and a memw signal can be generated from the

  Calculate the impulse response of the system

Digital Signal Processing (ELEC 0316) - Calculate the impulse response h[n] of the system and verify the output with matlab program.

  Report and the multisim design for your project

Conceptual Design: Explain the block diagram and what each block does (its functionality) and how it works. Also, be sure to explain when one might use an operational-amplifier wheatstone bridge and its advantages.

  Reconstruct the original narrowband signal

How would you reconstruct the original narrowband signal from the sampled versions of its in-phase and quadrature components?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd