Is the circuit inside the box a series or a parallel circuit

Assignment Help Electrical Engineering
Reference no: EM13262519

Suppose you have a "black box" with two electrical terminals. You are told that inside the box is an electrical circuit, composed of either a resistor and inductor; or a resistor and a capacitor. You are also told that the impedance between those terminals was measured with an input frequency of 1 KHz.

a) Is this impedance inductive, or capacitive?
b) What is the equivalent value of admittance (including phase angle)?
c) Is the circuit inside the box a series circuit, or a parallel circuit?
d) What are the component values (resistance, and capacitance or inductance) of the circuit?
e) What do you expect the impedance, and admittance, of the circuit will be if it is measured at 500 Hz?

Reference no: EM13262519

Questions Cloud

Find the thermal-equilibrium electron and hole concentration : Calculate the thermal-equilibrium electron and hole concentrations in a compensated p-type semiconductor. Consider a silicon semiconductor at T=300K in which Na = 10e16 cm-3 and Nd=3x1015 cm-3. Assume ni = 1.5 x1010 cm-3.
How much time is required for one leg to swing forward : An elephant's legs have a reasonably uniform cross section from top to bottom, and they are quite long, An elephant has legs that stretch 2.3 m from its shoulders to the ground. How much time is required for one leg to swing forward after completin..
Critical thinking-opinion essay : Your paper will be automatically submitted through Safe Assign when you upload it through the assignment link week
Explain atoms form a covalently-bonded diatomic molecule : When two atoms form a covalently-bonded diatomic molecule, the distance between the nuclei at which the potential energy is at a minimum is called
Is the circuit inside the box a series or a parallel circuit : You are told that inside the box is an electrical circuit, composed of either a resistor and inductor; or a resistor and a capacitor. You are also told that the impedance between those terminals was measured with an input frequency of 1 KHz.
Compute the percent yield of the mixed product : In our Ochem lab for nitration of bromobenzene we didn't further seperate the product mixture of 4-bromonitrobenzene and 2-bromonitrobenzene and yet we have to calculate the percent yield of the mixed product using percent distribution
Explain what is the concentration of ch3cooh : What is the concentration of CH3COOH (Ka = 1.8x10-5) in 50.0 mL of a 0.0187 M CH3COOH solution
Calculate and plot the ratio correction factor of the ccvt : The value of the capacitor from the high-voltage terminal to the tap point is 0.005µF. The tap point voltage is 4 kV. What is the value of the capacitor connected between the tap point and the ground terminal. What is the value of the tuning induc..
What you say by citing direct evidence from the magazines : Whenever possible back up what you say by citing direct evidence from the magazines. That is, select specific examples from the magazines that illustrate or support your general points.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How much work is done on the electron by the electric field

An electron is released from rest at a distance of 0.350 m from a large insulating sheet of charge that has uniform surface charge density 4.90×10^-12 C/m . A) How much work is done on the electron by the electric field of the sheet as the electron..

  Determine the cone angle that will match the line

(a) Determine the cone angle that will match the line to an infinite length biconical antenna. (b) For the cone angle of part (a), determine the two smallest cone lengths that will resonate the antenna.

  Explain capacitor and electric automobile

Do you think that an electric automobile based on capacitive energy storage is feasible?

  Determine binary code produced by adc quantization error

Assuming that a 12-bit ADC channel accept analog input ranges from 0 to 20 volts, determine the following a) number of quantization levels b) step size of the quantizer or resolution

  Implementation of ga matlab code

Project on LFC using tuned FOPID. I have considered a two area model. Need help regarding implementation of GA MATLAB code for a two area interconnected power system for LOAD FREQUENCY CONTROL.

  Find what is the power delivered to the resistor

a)What is the voltage across a 220? resistor if the current through it is 5.6 mA b)What is the current through a 6.8? resistor if the voltage drop across it is 24 V c) What is the power delivered by a 6 V battery if the current drain is 750mA

  Provide two design of shunt regulators utilizing zener diode

For both designs, the supply voltage is nominally 9 V and varies by +/- 1V. For the first design, assume that the availability of supply current is not a problem, and thus operate the diode at 20mA. For the second design, assume that the current f..

  What is an alternative to using a higher order anti-aliasing

1. A transfer function of a low pass filter may be divided into which three response ranges Actual response, ideal response, and straight-line response Gain, ripple, and roll-off Pass band, roll-off, and stop band Attenuation, gain, and roll-off

  What is the group delay between a pulsar pulse

the solutions at both frequencies about a total transit time of 1000 years (speed of light in a vacuum result) such that subtracting one from the other leaves just the delay that is of order of 1 second.

  Find the value of the lumped elements c and l

A.) We would like to use a series lumped element b to match this load. What is the length of the line where the normalized input impedance is z= 1-jb(d/\lambda). If the rfequency is 1GHz , find the value of the lumped element(C or L).

  Determine the sum or difference of two numbers

Use the simulation timing diagram to compare the worse case time to do an operation with your ALU with the worst case using the 74LS381. State which operation takes the longest and list the time required for both ALU's.

  Describe how to troubleshoot a communications problems

In the case of a problem in the communication process in general (not just using Fieldbus), describe how you would troubleshoot a communications problem at the physical layer. Describe also the tools that you would use to troubleshoot

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd