Internal energy stating whether it is increase of decrease

Assignment Help Mechanical Engineering
Reference no: EM13706648

During the compression stroke of an engine, the work done on the working substance in the engine cylinder is 75kJ/kg and the heat rejected to the surroundings is 42kJ/kg. Find the change of internal energy stating whether it is an increase of decrease.

Reference no: EM13706648

Questions Cloud

Angular velocity and angular acceleration of the slotted arm : If a slider block C is fixed to the disk that has a constant counter clockwise angular velocity of 4 rad/sec, determine the angular velocity and angular acceleration of the slotted arm AB at the instant shown.
Pressure and specific volume in isentropic compression : Starting from the ideal gas law and the first law of thermodynamics derive the relationship between a) pressure temperature and, b) pressure and specific volume in isentropic compression show detail proof.
Using exponential smoothing with a weight : Using exponential smoothing with a weight of 0.6 on actual values..If sales are $45,000 and $50,000 for 2010 and 2011, what would be the forecast for 2012? (First forecast is equal to the actual value of proceeding year)
How much heat is added to accomplish : A copper vessel of mass 2kg contains 6kg of water. If the initial temperature of the vessel plus water is 20C and the final temperature is 90C, how much heat is added to accomplish this change assuming that there is no heat loss?
Internal energy stating whether it is increase of decrease : During the compression stroke of an engine, the work done on the working substance in the engine cylinder is 75kJ/kg and the heat rejected to the surroundings is 42kJ/kg. Find the change of internal energy stating whether it is an increase of decreas..
Quantity of gas has an initial pressure : A quantity of gas has an initial pressure of 2.72MN/m^2 and a volume of 5.6dm^3(l). It is expanded according to the law PV^1.35 = C down to a pressure of 340kN/M^2. Determine the final volume and work done.
Measures a wind tunnels velocity n times : During an experiment, an aerospace engineering student measures a wind tunnel's velocity N times. The student reports the following information, based on 90% confidence, about the finite data set: mean velocity=25 m/s, velocity standard deviation=1.5..
Determine the new volume of the gas : 0.112m^3 of gas has a pressure of 138kN/m^2. It is compressed to 690kN/m^2 according to the law PV^1.4 = C. Determine the new volume of the gas.
In a non-flow process there is a heat loss : In a non-flow process there is a heat loss of 1055kJ and an internal energy increase of 210kJ. How much work is done and is the process an expansion or compression?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the net power output developed by the turbine in

steam at 160 bar 520 degrees celsius and with a mass flow rate of 250 kgs enters a turbine operating at steady state

  At one point in the duct the pressure and temperature are

assume that the flow of air through a given duct is isentropic. at one point in the duct the pressure and temperature

  Specify efficiency of the gear train as a percentage

Determine an equation for the efficiency of the gear train in terms of the load (torque) on shaft 2 and determine the input power required at shaft 1.

  Calculate the composition of both elements in mass percent

sterling silver is a metal alloy containing silver and copper. calculate the composition of both elements in mass

  What is the maximum rate at which work could be obtained if

two streams of air are mixed in a steady state process. assume air is an ideal gas with a constant heat capacity cp72r

  Draw a t-s diagram be sure to label the states 122s344s

superheated steam at 120 bar and 520c leaves the steam generator of a vapor power plant and enters a turbine with an

  Determine the work per unit mas of air for an adiabatic

air as an ideal gas is compressed from a state where the pressure is 0.1 mpa and the temperature is 27o to a state

  What is the percent span for the old and new setpoints

In order to increase production rate, a reactor setpoint was increased from 160 psig to 190 psig. The reactor pressure transmitter was recalibrated from 0- 200 psig to 0- 300 psig. What is the percent span for the old and new setpoints?

  What degree of superheat would be required if the team

the condensation that can occur in the low-pressure end of a steam turbine is undesirable because it can cause

  The steam then enters the second stage and exits at 147

a well-insulated turbine operating at steady state has two stages in series. steam enters the first stage at 800

  Define shearing stress

Two bars, one having a circular section of radius b, the other an elliptic section with semiaxes a,b. For equal angles of twist, which bar experiences the larger shearing stress?

  The measurement is to be performed with an uncertainty of

a pneumatic displacement gage is to be used to measure displacement between 0.1 and 0.2 mm. the output of the device is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd