Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The linkage shown below is made up of two 3-kg rectangular members (0.4 m by 0.1 m), and is flying through the air. At the instant shown, the vertical member has angular velocity 4 rad/s, and the angled member has angular velocity 1 rad/s.
a. What force vector does the angled member apply to the vertical member (use the inertial CS drawn in the top right corner of the figure)?
b. In the non-inertial CS fixed at the top of the vertical member, the motion of the point A is different than the motion calculated in an inertial CS. Give a differential equation for the position of A in this NICS.
given that E for the tube material is 70 GN/m2 and the stool legs are 75cm long, how much will each leg shorten under the applied compressive load (take g = 9.8m/s2)
Determine the size PFR and CFSTR's required to treat 4000 m3/day of sewage with a BOD of 200 mg/L. State law requires a minimum of 92% removal and BOD follows first order kinetics.
A water treatment plant treats a continuous flow rate of 50,000 m^3/day and plans to build a 10,000 m^3 tank to house an additional treatment process. What will be the steady-state effluent concentration of an ideal CSTR
A rectangular channel carries a discharge of 2.00 m3/sec per meter of channel width over a weir crest that is 1.4 m in height. The energy grade line upstream of the weir measure 2.7 m above the channel bottom.
A two-dimensional incompressible flow field is defined by the velocity components u=2V(x/L-y/L) and v=-2V(y/L). where V and L are constants. If they exist, Find the stream function and velocity potential funtion
A force of 100 000 N is applied to a 10 mm x 20 mm rectangular cross-section iron bar in tension. If the iron has a yield strength of 400 MPa and a tensile strength of 480 MPa, determine: whether the bar will plastically deform
Determine the minimum force P to prevent a 30kg rod AB from sliding on a wall. The contact surface at B is smooth, whereas the coefficient of static friction between the rod and the wall at A is Us=0.2.
A flow of 125,000 gallons per day enters a sedimentation basin which is 20 feet wide, 60 feet long and 12 feet deep. What is the minimum settling velocity of a particles that will be 100% removed by the basin
Ethylene enters a turbine at 10 bar and 450 K, and exhausts at (atm) and 325 K. For mass flow in = 4.5 kg s^-1, determine the cost C of the turbine. State any assumptions you make. Data: H1 = 761.1 , H2 = 536.9 kg^-1, C/$ = (15,200)(1W1/kW)^0.573
The bund channel is to be formed by the embankment only. The horizontal distance between two bund s is 50 m. The 1-hr rainfall expected during the recurrence interval of 10 yrs is 8 cm/hr.
write computer code using Matlab that emoloyes the nelder and mead simplex method to solve the welded-beam design (benchmark problem
material (LCY) in 12 yard dump trucks, placing it, and compacting the weight of the soil is 3,750 lb/cu.yd. (30 pts.) (show your calculations) a) Find the Swell and Shrinkage b) Load and Shrinkage Factors
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd