Implement carry-out and sum functions for 1-bit full adder

Assignment Help Electrical Engineering
Reference no: EM13274313

1. Implement the carry-out and sum functions for a 1-bit full adder using a 3-to-8 decoder block with active-low outputs and additional gates (what gate types should be used).
Complete the truth table and draw the circuit diagram
Inputs: Outputs:
Cin A B Cout S
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1

2. Implement the following function with a 3x8 decoder with active-high outputs and a input logic gate

Reference no: EM13274313


Write a Review


Electrical Engineering Questions & Answers

  Compare field at center of helmholtz coil pair and solenoid

Compare the field at the center of a Helmholtz coil pair and at the center of a solenoid, if both use the same total length of wire and carry the same current.Take the solenoid length equal to the spacing between the Helmholtz coils

  Give the solution to power factor

The solution to Power Factor, Two single-phase loads are connected in parallel across a 415 V, 50 Hz supply. One load is rated 130 kW at a power factor of 0.75

  How many quantization bits must be used to satisfy

An analog signal ranging between 0 and 1 V must be quantized. The midrange quantization errors must be no greater than 0.1V. How many quantization bits must be used to satisfy this requirement

  What must the magnitude of the charge in micro coulombs

The space between the plates is then filled with a dielectric material, with dielectric constant k = 6.55. What must the magnitude of the charge in micro coulombs on each capacitor plate now be, to produce the same potential difference between the..

  Compare by hand solution and pspice simulation for a voltage

Compare the by hand solution and the PSPICE simulation for a voltage amplifier which has an input resistance of 10kohms and an output resistance of 100ohms, and a gain of 100V/V. The voltage amplifier is capacitively coupled to a voltage source.

  What would be the baud rate if the intial value of the timer

Write a sequence of instructions to initialize and run the timer to geneate an 800 baud rate clock. what would be the baud rate if the intial value of the timer was set to 9AH

  What is probability of getting ford given that is a new car

assume that the probability that a new car is chosen given that its a fiat and nissan are .75 and .6 respectively. also the probability that an arbitrarily chosen car is a ford and nissan are 0.2 and 0.4 respectively. now, what is the probability ..

  Explain using diagram

If L=0.0053nH, C=15µF find the operating frequency of series LC circuit. What factors decides capacitance? Explain using diagram.

  What is smallest power of 2 needed to generate binary code

What is the smallest power of 2 needed to generate a binary codeword long enough for this message i.e. find N (= 2k) = What is the maximum number of binary digits that can be generated with this choice of N

  How many pulses are needed from the controller every second

A 3-Phase stepping motor is to be used to drive a linear axis for a robot. The motor output shaft will be connected to a screw thread with a screw pitch of 5 mm. We want to be able to have a spatial control of at least 0.1 mm.

  Find the developed power and power lost in ra

A shunt dc motor has RA= .1 ohmn and VT = 440 V. For an output power of 50 hp, we have nm=1500 rpm and IA = 103 A. The field current remains constant for all parts of this problem.

  Calculate the average torque and maximum torque

When the two windings are connected to a a.c supply of 50hz, the field current is 0.1A, the armature current is 100A and the phase difference between them is 60 degree. calculate the average torque and maximum torque.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd