Illustrate and annotate the lever system

Assignment Help Civil Engineering
Reference no: EM13210732

a wheel barrow is used to lift a 200lb load. the lenght from the wheel axle to the center of the load is 2ft. the length from the wheel and axle to the effort is 5 ft. illustrate and annotate the lever system.

Reference no: EM13210732

Questions Cloud

Find out the rms speed of nitrogen and oxygen : Air is mostly nitrogen and oxygen. Determine the rms speed of nitrogen and oxygen at room temperature (20° C).
Created several unanticipated problems-maternity care : This would mean that a patient, who may need cardiac or maternity care, may need to drive 50 miles and pass 4 or 5 good hospitals in the plan in order to get the care they needed at Verde Greene Hospital.
Design a column base plate : Design a column base plate for a W10 x 33 column supporting a service dead load of 20 kips and a service live load of 50 kips. The column is supported by a 12-inch x 12-inch concrete pier. Use A36 steel and f 'c = 3 ksi. Answer 12 x 12 x 5/8
Explain nist-janaf table deltag standard formation values : NIST-JANAF table deltaG standard formation values at 5400 K for N(g), O(g) and NO(g) are 113.817 kJ/mol, -108.155 kJ/mol and 23.568 kJ/mol.
Illustrate and annotate the lever system : a wheel barrow is used to lift a 200lb load. the lenght from the wheel axle to the center of the load is 2ft. the length from the wheel and axle to the effort is 5 ft. illustrate and annotate the lever system.
Explain cbr method of pavement design : Explain CBR method of pavement design with one example.
Explain how many liters of chlorine gas can be produced : How many grams of aluminum metal and how many liters of chlorine gas can be produced by passage of 4.8 amp of current for 2.3 hours under standard conditions
Determine the relevant pi groups : The break up of a liquid jet into droplets of diameter d depends on the jet diameter D, the jet velocity V, viscosity Mu, density rho,and surface tension sigma.
Companys year-end inventory turnover ratio : What are your forecasts of the companys year-end inventory turnover ratio? Round your answer to two decimal places.

Reviews

Write a Review

Civil Engineering Questions & Answers

  How much does the aggregate in the wheelbarrow weight

you fill a 2-cubic foot wheelbarrow to the top with aggregate. if the specific gravity of the aggregate is 2.548 and 18% of the aggregate is void spaces, how much does the aggregate in the wheelbarrow weight?

  Establishing a horizontal distance

A tape is calibrated and found to measure 100.04ft between the 0- and 100-ft marks. What measurements should be laid out to establish a horizontal distance of 682.25ft?

  Find the shortest ladder

a wall 8 ft high is 3/3/8 ft. from a house. find the shortest ladder which will reach from the ground house when leaning to the wall.

  Determine the torsional buckling stress

determine the torsional buckling stress for the compression member if the length is 4m and cross section is the form shown. the ends are restrained such that there are not free to warp.given A:5646mm2 Ix:42.63Mmm4 Iy:14067Mmm4 E:210kN/mm2 G:80kN/m..

  Shear tension and bending of the fixed i-beam

To satisfy desige limitation it is necessary to determine the effect of the 2- kN tension in the cable on the shear tension and bending of the fixed I-beam.

  Superelevation rate for a roadway

What superelevation rate would you recommend for a roadway with a design speed of 100 km/hr and a radius of curvature of 500 m? Assume f = 0.11.

  Magnitude of the acceleration of the train

The train passes point A with a speed of 30 m/s and begins to decrease its speed at a constant rate of at = - 0.25 m/s2. Determine the magnitude of the acceleration of the train when it reaches point B, where sAB = 412 m.

  Determine the volume flow rate

Water with a static pressure of 1.96kN/M2 flows through an 800 mm diameter pipe. A pitot tube pressure gage in this pipe reads a pressure of 5.88 kN/M2. How do you determine the volume flow rate (Q) of the water? (Q = 1.40 M^3/sec, V=2.79 M/sec)

  Assist structural engineer for a bridge replacement project

You should provide the structural engineer with a formal typed report that will include all of your analyses and final size of the footing. You should also include all of your design assumptions in your report.

  Measure the distance pa, pb, pc

Measure the distance PA, PB, PC etc. from p to various point with chain or tape and plot them to scale along the co responding rays. Join the points a, b, c, etc. to give outline of survey.

  Description of the soil characteristics

For each of the horizons, provide a description of the soil characteristics and briefly describe the environment where you would expect to find the horizon?

  Shear force-bending moment diagrams

A three-span continuous beam ABCD with three equal spans supports a uniform load with intensity q. Determine all reactions of this beam and draw the shear force and bending moment diagrams labelling all critical ordinates.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd