If you wanted to transfer 100 kj from on reservoir to the

Assignment Help Mechanical Engineering
Reference no: EM13632192

There are two thermal reservoirs: the hot reservoir is at 1200 K and the cold reservoir is at 600 K. If you wanted to transfer 100 kJ from on reservoir to the other, what would the change in entropy of the two reservoirs be?

Reference no: EM13632192

Previous Q& A

  A 025kg block is held compressed 01m against a spring

a 0.25kg block is held compressed 0.1m against a spring k1000nm. what is the max height of the block after it is

  A 3000lb car is traveling at 60mih up an inclined surface

a 3000lb car is traveling at 60mih up an inclined surface of 5deg when the brakes are applied creating a constant

  Show the hypotheses the claim the test statistic the df the

a sociologist wishes to determine whether there is a relationship between the sex of a person and the amount of alcohol

  A double acting cylinder with a single rod must produce a

a double acting cylinder with a single rod must produce a thrust of 80kn and move out with a velocity of 3mms on the

  A carnot heat engine operates between 40c and 320 c what

a carnot heat engine operates between 40c and 320 c. what is the thermal efficiency? if the work output is 200 kjkg

  If a 1 micro-coulomb charge is next to a 4 micro-coulomb

if a 1 micro-coulomb charge is next to a 4 micro-coulomb charge the magnitude of the repulsive force on the 1

  An injected slug of tracer material flows with its carrier

an injected slug of tracer material flows with its carrier fluid down a long straight pipe in dispersed plug flow. at

  Construct a 99 confidence interval estimate of the mean of

construct a 99 confidence interval estimate of the mean of the differences between volumes for the first born and the

  Calculate the percent of the total resistance for external

1. calculate the percent of the total resistance for external diffusion internal diffusion and surface reaction.2.

  If a neutral metal sphere is connected to ground through a

if a neutral metal sphere is connected to ground through a wire when a positively charged glass rod comes close to the

Reviews

Write a Review

 

Similar Q& A

  A load of 500 pounds is placed on a cylinder of 1040

a load of 500 pounds is placed on a cylinder of 1040 carbon steel with a 2 inch radius. calculate the stress in

  Air and rolling resistance of the car may be neglected find

a dragster weighing 7120n attains a speed of 430km in the quarter mile.immediately after passing through the timing

  Calculate the mean velocity of the water

A new cast iron pipe is 5 km long and 15 mm diameter is used to convey water at a rate of 0.0150m3s-1. Given the absolute roughness of the pipe is 0.26 mm, density of water is 998 kg/m3 and dynamic viscosity of water is 1.14 × 10-3 kgm 1s-1.

  A 10 kg slab of cr-v steel at 900 c is to be quenched by

a 10 kg slab of cr-v steel at 900 c is to be quenched by immersing in a vessel of water. assume the slab exhibits a

  Determine the range of values of p

Two slender rods of negligible weight are pin-connected at A and attached to the 18-lb block B and the 80-lb block C as shown. The coefficient of static friction is 0.55 between all surfaces of contact. Determine the range of values of P for which..

  Would each process require the same amount of work if not

suppose you needed to reduce the diameter of a rod 20 and could choose between drawing it or extruding it through the

  Determine the power kw for the compressor if the inlet

air enters a compressor at 179 kpa and 290 k and exits at a temperature of 500.9 k. determine the power kw for the

  A mummy picks up a calculator and starts adding odd whole

a mummy picks up a calculator and starts adding odd whole numbers together in order 135....etc. what will be the last

  Heat is slowly removed from the steam during a constant

saturated steam at 2 mpa is contained in a piston-cylinder device. the initial volume is 0.25 cubic meters. heat is

  Determine the pressure p2 and p3 in pipes 2 and 3 under the

water flows through the horizontal y-fitting shown in figure p3.101. if the flowrate and pressure in pipe1 are q1 2.3

  What are the conditions for valid object representation in

do you think the objects created in the following representation schema are always valid? justify your answers with

  We wish to calculate the mass of steam required per unit

a closed feedwater heater for a steam power plant operates as shown in the figure below. high-pressure liquid water at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd