User Account

All Pages

A double acting cylinder with a single rod must produce a

Assignment Help Mechanical Engineering
Reference no: EM13632188

A double acting cylinder with a single rod must produce a thrust of 80KN and move out with a velocity of 3mm/s on the out stroke. The operating pressure is 100barg. Calculate the bore diameter and the flow rate of oil. If the hydro-mechanical efficiency is 0.95, the rod diameter is 25mm and the oil pressure & flow are the same in both the retraction and advance strokes what would be the force and speed in the retraction direction?

Reference no: EM13632188

Questions Cloud

If you wanted to transfer 100 kj from on reservoir to the : there are two thermal reservoirs the hot reservoir is at 1200 k and the cold reservoir is at 600 k. if you wanted to
A 025kg block is held compressed 01m against a spring : a 0.25kg block is held compressed 0.1m against a spring k1000nm. what is the max height of the block after it is
A 3000lb car is traveling at 60mih up an inclined surface : a 3000lb car is traveling at 60mih up an inclined surface of 5deg when the brakes are applied creating a constant
Show the hypotheses the claim the test statistic the df the : a sociologist wishes to determine whether there is a relationship between the sex of a person and the amount of alcohol
A double acting cylinder with a single rod must produce a : a double acting cylinder with a single rod must produce a thrust of 80kn and move out with a velocity of 3mms on the
A carnot heat engine operates between 40c and 320 c what : a carnot heat engine operates between 40c and 320 c. what is the thermal efficiency? if the work output is 200 kjkg
If a 1 micro-coulomb charge is next to a 4 micro-coulomb : if a 1 micro-coulomb charge is next to a 4 micro-coulomb charge the magnitude of the repulsive force on the 1
An injected slug of tracer material flows with its carrier : an injected slug of tracer material flows with its carrier fluid down a long straight pipe in dispersed plug flow. at
Construct a 99 confidence interval estimate of the mean of : construct a 99 confidence interval estimate of the mean of the differences between volumes for the first born and the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Estimate the theoretical fracture strength of a brittle

estimate the theoretical fracture strength of a brittle material if it is known that fracture occurs by the propagation

  Explain whether this pressure cooker is operating under

a 4 l volume of pressure cooker in a kitchen operates at 200 kpa with an exit area of 10 mm2. with well controlled heat

  Find how much should be cut off from free length of the

a helix compression spring is manufactured using the following parametersod1.00id.790wire dia 0.105fo 40.49 lbf

  Two blocks a and b of mass 8 kg and 12 kg respectively hang

two blocks a and b of mass 8 kg and 12 kg respectively hang from a cable which passes over a pulley of negligible mass.

  A tank of propane has capacity of 120 gallons what would

a tank of propane has capacity of 120 gallons what would the tank be rated in terms of cubic feet cubic meters and

  How many times could you push this 50 kg block of steel

suppose you have a 50 kg block of steel. if you have 103 exajoules at your disposal how many times could you push this

  Describe some of the important steps in the preparation of

1- describe some of the important steps in the preparation of a written document. what role do written documents play

  A mixing chamber steadily mixes a hot water stream at

a mixing chamber steadily mixes a hot water stream at 80degc and 0.5kgs rate with a cold water stream at 20degc. if the

  A cylindrical duct supplies 120 kgs of combustion air at

a cylindrical duct supplies 1.20 kgs of combustion air at 150 c and 95.0 kpa to a furnace. if the velocity of the air

  A polymer component that needs to maintain a stress level

a polymer component that needs to maintain a stress level above 10 mpa for proper functioning of an assembly is

  Steam enters a nozzle at 30 bars and 320c and leaves at 15

steam enters a nozzle at 30 bars and 320c and leaves at 15 bars with a velocity of 535 ms. the mass flow rate is 8000

  Determine the velocity v and acceleration a determine the

a moving particle has coordinates in millimeter which vary with the time t in seconds according to r2t2-4ti 3t2 -t33j

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd