User Account

All Pages

If the work output is 1000 kjkg calculate the maximum

Assignment Help Mechanical Engineering
Reference no: EM13643637

An otto cycle is proposed to have a compression ratio of 10:1 while operating with the low air temperature of 277 degree C and a low pressure of 200 kpa. If the work output is 1000 kj/kg, calculate the maximum possible thermal efficiency and compare with carnot cycle. Also, calculate the MEP. Assume constant specific heats.

Reference no: EM13643637

Questions Cloud

Derive an expression for the terminal velocity of the bar : a rectangle frame of conducting wire has negligible resistance and width w and is held vertically in a magnetic field
Determine the time at which the velocity is equal to zero : the equation below defines the acceleration of a particle where a is in ms2 and t is in seconds. determine the position
Calculate the mass feed rate of hydrogen kgs required : acetylene is hydrogenated to form ethane c2h6. the feed to thereactor contains 1.5 mol h2mol c2h2.a. calculate the
Ch3cl aq oh- aq ----gt ch3oh aq cl- aqnbspnbsp : consider the reaction of chloromethane with oh- in aqueous solutionnbspnbspnbspkfch3cl aq oh- aq ----gt ch3oh aq cl-
If the work output is 1000 kjkg calculate the maximum : an otto cycle is proposed to have a compression ratio of 101 while operating with the low air temperature of 277 degree
A 071-um-diameter droplet of oil having a charge of is : in the early 1900s robert millikan used small charged droplets of oil suspended in an electric field to make the first
The cycle work is 1000 kjkg what is the compression ratio : an engine operates on the air standard otto cycle. the cycle work is 1000 kjkg. what is the compression ratio of the
In the first 130 of this reaction the concentration of : consider the following reaction2hbr g--gt h2 g br2 gin the first 13.0 of this reaction the concentration of dropped
An air standard otto cycle has the following cycle states : an air standard otto cycle has the following cycle states where state a is the beginning of the isentropic compression

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The given figure depicts an indirectly fired gas turbine

the given figure depicts an indirectly fired gas turbine engine. in the gas turbine engine air is compressed to a high

  The pressure is 100 psia and during this process the volume

a reversible carnot heat engine has 1.00 lbm of air as the working fluid. heat is received at 740 degrees f and

  A fixed quantity of air at t1 60oc and p1 158 kpa is

a fixed quantity of air at t1 60oc and p1 158 kpa is heated at constant temperature in a piston-cylinder assembly

  A frictionless piston-cylinder device contains 2 kg of

a frictionless piston-cylinder device contains 2 kg of nitrogen at 100 kpa and 300k. the nitrogen is compressed in a

  Make a form tool for lathe for making a convex groove

Make a form tool for lathe for making a convex groove of 3 mm radius. tool material will be tungsten carbide. Know the dimensions of tool.

  Draw a t-s diagram of the process through the cycle neglect

a gas refrigeration system composed of a turbine a compressor and two heat exchangers is operating at steady state. air

  State what the joints are in the system

State what the joints are in the system and knowledge of computational kinematics explain what you believe is the procedure to calculate each variable.

  Implement the controller using mechanical components

Analyze the given plant for its performance in time and frequency domains (transient response, Routh-Hurwitz test, root locus, Nyquist criterion, Bode plot, Nichols chart).

  Is the hoop stress in a 12 schedule 40 pipe greater or

is the hoop stress in a 12 schedule 40 pipe greater or smaller than the axial stress? by how much? so how will the pipe

  The combustion gases leave the heat exchanger at 380 k

the top cycle of a combined cycle power plant has a pressure ratio of 12. air enters the compressor at 300 k at a rate

  The wood beam has an allowable shear stress of 7 mpa

the wood beam has an allowable shear stress of 7 mpa. determine the maximum shear force v that can be applied to the

  Determine the power transmitted to the pulley in horsepower

an object whose mass is 50 lb attached to a rope wound around a pulley. the radius of the pully is 3 in. if the mass

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd