User Account

All Pages

An air standard otto cycle has the following cycle states

Assignment Help Mechanical Engineering
Reference no: EM13643633

An air standard otto cycle has the following cycle states, where state A is the beginning of the isentropic compression; P1= 101 kpa, T1=333K, V1=0.28 cubic meter, T3=2000K, r=5. Determine a) the remaining cycle states points; b) the heat added; c) heat rejected and d) thermal efficiency.

Reference no: EM13643633

Questions Cloud

If the work output is 1000 kjkg calculate the maximum : an otto cycle is proposed to have a compression ratio of 101 while operating with the low air temperature of 277 degree
A 071-um-diameter droplet of oil having a charge of is : in the early 1900s robert millikan used small charged droplets of oil suspended in an electric field to make the first
The cycle work is 1000 kjkg what is the compression ratio : an engine operates on the air standard otto cycle. the cycle work is 1000 kjkg. what is the compression ratio of the
In the first 130 of this reaction the concentration of : consider the following reaction2hbr g--gt h2 g br2 gin the first 13.0 of this reaction the concentration of dropped
An air standard otto cycle has the following cycle states : an air standard otto cycle has the following cycle states where state a is the beginning of the isentropic compression
The bullet imbeds itself into the block and they start to : a 25 gram bullet moving at 550 ms strikes and imbeds itself in a 3.5-kg wooden block that is at rest on a level
Using activities calculate the ph of a solution containing : using activities calculate the ph of a solution containing 0.010 m naoh plus 0.012 m lino3. what would be the ph if you
If 189 of 0800 solution are needed to neutralize 500 of a : if 18.9 of 0.800 solution are needed to neutralize 5.00 of a household ammonia solution what is the molar concentration
The pressure and temperature at the end of compression : an engine operates on an air standard otto cycle with the compression ratio of 91. the pressure and temperature at the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine a velocity versus time graph of their descent and

a skydiver of weight 84kg jumps from a plane 3300m above the ground. they initially free fall for a period of seconds

  A shaft with a diameter of 100 mm rotates at 1500 rpm a

a shaft with a diameter of 100 mm rotates at 1500 rpm. a fluid-film bearing is designed to support a 5 kn load. assume

  Using the properties of water for the drink determine the

during a picnic on a hot summer day all the cold drinks disappeared quickly and the only available drinks were those at

  Determine the distance the cart will move down the inclined

the 20-lb car is released from rest at time t0 on the inclined surface. the force p 8t lb acts on the cart where t is

  The contact length and force are 25 in and 1 ton

the wheel of a crane lift is rolling on a flat rail. the radius of the wheel is 4 in the contact length and force are

  The vessel is heated until the water pressure reaches 8 mpa

a closed rigid pressure vessel is filled with a saturated mixture of 1.78 kg of liquid water and 0.22 kg of water vapor

  Dtermine a the compressor power in kw b the refrigerating

a vapor compression refrigeration cycle operates at a steady state with refrigerant 134a as the working fluid.

  How much is the velocity at the outlet for each case if the

for the piping diameter changes and flow directions shown below if the velocity at the input is 5 ms the initial

  Air within a piston-cylinder assembly initially at 12bar

air within a piston-cylinder assembly initially at 12bar 327 degree celcius undergoes an isentropic expansion to

  A longitudinal fin with b30 cm is made of aluminum k237

a longitudinal fin with b30 cm is made of aluminum k237 wm-k and has a base temperature of 80oc. the fin

  Find the force required for the direct extrusion of

find the force required for the direct extrusion of commercially pure aluminum 1100-o billet 8 in in diameter into a

  Obtain a plot of the approximate transfer function model

the volume of a hemispherical storage tank as a function of its height is given by vt pirh2t - pi3h3t where r is the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd