If the plate is held at 30c determine the average heat

Assignment Help Mechanical Engineering
Reference no: EM13628704

In a chemical processing plant, glycerin flows over a 1 m long heated at plate at free-stream conditions V = 3 m/s and T1= 10C. If the plate is held at 30C, determine the average heat transfer per unit width, assuming that the critical Reynolds number, Re = 500,000.

Glycerin (for reference)

Density = 1259.9

cp = 2.427

viscosity = 79.9(10^-2)

v = 634(10^-6)

k= 286(10^-3)

alpha = 0.935(10^-7)

Pr = 6780

Reference no: EM13628704

Questions Cloud

How far was the laser originally from the object in meters : turning a laser you shine the beam on an object located nearby and observe the interference pattern with a suitable
In a long solenoid the density of the wire is 180 turnscm : in a long solenoid the density of the wire is 180 turnscm. if the current in the wire is 0.680a what is the strength of
If the speed variation from max to min is not to exceed 02 : a punching machine is driven by a motor which exerts a constant torque on the flywheel at a mean speed of 2 revs. if
If no preliminary sample is taken to estimate p how large a : a ponderosa pine forest in colorado has a pine beetle infestation. the beetles bore into a tree and carry a fungus
If the plate is held at 30c determine the average heat : in a chemical processing plant glycerin flows over a 1 m long heated at plate at free-stream conditions v 3 ms and t1
Two long parallel wires carry currents of 0245 a in the : two long parallel wires carry currents of 0.245 a in the same direction. if the wires are 0.034 m apart what is the
The maximum discharge is 3000 cfs when the head on the : an ogee spillway of a gravity dam is to be modeled using water. the spillway section is 40 feet high its crest length
A water stream is heated in fully developed flow through a : a water stream is heated in fully developed flow through a pipe with uniform heat flux at the wall. the flow rate is
Derive an expression for the water level height ht as a : a cyndrical tin can with diameter d1 85mm has circular hole drilled in the bottom with diameter d2 6.35 mm. initially

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  A cylinder having an initial volume of 3 msup3 contains 01

a cylinder having an initial volume of 3 msup3 contains 0.1 kg of water at 40ordmc. the water is then compressed in an

  The central cubical area of an office building at sea level

the central cubical area of an office building at sea level has a floor area of 4000 ft2 and is occupied by 30 people

  A piston-cylinder device initially contains 025 kg of

a piston-cylinder device initially contains 0.25 kg of nitrogen gas at 130 kpa and 180degc. the nitrogen is now

  By how much will the bullets miss the target

a hunter aims directly at a target 140 meter away. if the bullet leaves the gun ay a speed of 280 m/s, by how much will the bullets miss the target?

  Assuming that both the turbine and the pump are isentropic

consider a reheat cycle with steam leaving the boiler and entering the turbine at 4 mpa and 400 c . after expanded in

  If the surface temperature of the channel is maintained at

a channel of square shaped cross section30mm by 30mm carries water at a rate of m 2kgs. the channel length is l 10m

  95 of bodys volume is in the water while 5 of her bodys

according to archimedes principle the mass of a floating object equals the mass of the fluid displaced by the object. a

  An egg can be approximated as a 55 cm diameter sphere with

an egg can be approximated as a 5.5 cm diameter sphere with rho 1020 kgm3 cp 3.32 kjkgc. determine the heat transfer

  Explain layer of steel on the inner surface

An oven door consists of a layer of asbestos sandwiched between a layer of steel on the inner surface and a layer of wood on the outer face

  A carnot heat engine receives 1200 kj of heat per cycle

a carnot heat engine receives 1200 kj of heat per cycle from a high-temperature source at 925degc and rejects heat to a

  What is the sine wave generated by a phasor

what is the sine wave generated by a phasor of length 9, rotating with an angular velocity of 325 rad/s; and with the phase angle of 0."

  Half of the work produced by the engine is used to drive

an internally reversible heat engine operates between the temperatures of 827deg c and 17 deg c and rejects 100 kj min

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd