User Account

All Pages

Derive an expression for the water level height ht as a

Assignment Help Mechanical Engineering
Reference no: EM13628700

A cyndrical tin can with diameter D_1= 85mm, has circular hole drilled in the bottom with diameter D_2= 6.35 mm. initially, at time t=0 sec, the tin can is filled with water to height of h_0= 103 mm. Derive an expression for the water level height h(t) as a function of time and determine the time it takes to drain. Assume the flow is incompressible and inviscid (i.e. use bernoulli).

Reference no: EM13628700

Questions Cloud

If the plate is held at 30c determine the average heat : in a chemical processing plant glycerin flows over a 1 m long heated at plate at free-stream conditions v 3 ms and t1
Two long parallel wires carry currents of 0245 a in the : two long parallel wires carry currents of 0.245 a in the same direction. if the wires are 0.034 m apart what is the
The maximum discharge is 3000 cfs when the head on the : an ogee spillway of a gravity dam is to be modeled using water. the spillway section is 40 feet high its crest length
A water stream is heated in fully developed flow through a : a water stream is heated in fully developed flow through a pipe with uniform heat flux at the wall. the flow rate is
Derive an expression for the water level height ht as a : a cyndrical tin can with diameter d1 85mm has circular hole drilled in the bottom with diameter d2 6.35 mm. initially
The density if water at sixty degrees fahrenheit and : the density if water at sixty degrees fahrenheit and atmospheric pressure is sixty-two point four lbmft3. what is the
The crew of an enemy space craft attempts to escape from : the crew of an enemy space craft attempts to escape from your spacecraft by moving away from you at 0.281 of the speed
It is desired to estimate the mean time of continuous use : it is desired to estimate the mean time of continuous use until a wireless router will first required service. if it
Some plastic rods are automatically cut into lengths of 6 : some plastic rods are automatically cut into lengths of 6 in. actual lengths are normally distributed about a mean of 6

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The car then slows down to a velocity of 30 mihr in an

a car starts from rest and accelerates at a constant rate until it reaches 85 mihr in a distance of 110 ft at which

  Due to the drag resistance of the fluid the projectile

a small projectile is fired vertically downwards into a fluid medium with an initial velocity of 60 ms. due to the drag

  Determine the total length of the 12 tube that is required

a heater is required to supply the domestic hot water dhw in a 50 unit apartment building where the dhw load is

  If the refrigerator is reconfigured to work as a heat pump

a refrigerator operates with a coefficient of performance of 4.2 and requires an electrical input of 700 w. if the

  Determine the surface temperature of the wire

Determine the surface temperature of the wire during a windy day when the air temperature is 10°C and the wind is blowing across the transmission line at 50 km/h.

  What is the output variable

A process with Gp= 2/(2s+1) and Gd=1/(2s+1) experiences a disturbance step change of magnitude 5. The SP remains constant. If a P-controller alone with Kc=1 is used and Ga=Gs=1, then what is the output variable, delta Y(t) versus time?

  A design specification requires that a 1008 pound vehicle

a design specification requires that a 1008 pound vehicle be able to climb a 38 degree incline at 43 mph. what is the

  1 write a program that takes the image tracksjpg and finds

1 write a program that takes the image tracks.jpg and finds canny edges and then finds lines in these edges using the

  Calculate the work produced by the turbine the heat that

1000 kghr of water at 1 bar is fed to a pump where the pressure of the water is increased to 20 bar in an adiabatic

  After a reaction time of 0900s the policeman begins to

a police car is traveling at a velocity of 15.0 ms due north when a car zooms by at a constant velocity of 37.0 ms due

  Estimate the average temperature the wall will attain

Assuming that the air is 80°F and 1 atm and blows across the wall as on a flat plate, estimate the average temperature the wall will attain for equilibrium conditions.

  Explain beam deflection at corner through centroid

Beam deflection at corner through centroid, Sometimes the term centroid throws me for a loop. So, how would I set this problem up?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd