If the maximum temperature of the cycle is 2200k determine

Assignment Help Mechanical Engineering
Reference no: EM13631095

Consider an air standard Otto cycle with a compression ratio of 8. The engine inlet conditions are P=100 kPa, T=290K, and the bottom dead center volume is 400 cm3. If the maximum temperature of the cycle is 2200K, determine: (a) the heat addition in kJ, (b) the net work in kJ, (c) the thermal efficiency (%), and (d) the mean effective pressure in kPa. Use variable specific heats.

Reference no: EM13631095

Questions Cloud

During the process the pressure and specific volume are : water vapor in a piston-cylinder assembly undergoes a process from saturated vapor at 150 c to a pressure of 300 kpa.
A 45 wt pb-55 mg alloy is rapidly quenched to room : a 45 wt pb-55 mg alloy is rapidly quenched to room temperature from an elevated temperature in such a way that the high
An isentropic steam turbine processes 5kgs of steam at 4mpa : an isentropic steam turbine processes 5kgs of steam at 4mpa. the majority of this steam is exhausted at 50kpa and 100
Your family grows over time and the required water supply : suppose you build a rural house where you need to run a pipe to the nearest water supply which fortunately is about 1
If the maximum temperature of the cycle is 2200k determine : consider an air standard otto cycle with a compression ratio of 8. the engine inlet conditions are p100 kpa t290k and
At location one fluid with a density of 121times103 kgm3 is : the equation of continuity states the mass flow rate has the same value at every position along a tube that has a
A car with a mass of 1570 kg is supported by four springs : a car with a mass of 1570 kg is supported by four springs each with a spring constant of 25 nmm. in traveling over an
A metal block of mass 1220 kg is hanging from a string the : a metal block of mass 1.220 kg is hanging from a string. the tension in the string is 7.712 n. the block is submerged
Calculate the critical radius for a nickel embryo nucleus : calculate the critical radius for a nickel embryo nucleus that is undercooled 150 degrees c. the melting point of ni

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the static thrusts of the rocket and turbojet

calculate the static thrusts of the rocket and turbojet engine described in the figure. the thrust t is the force

  Air is compressed by a 30-kw compressor from p1 to p2 the

air is compressed by a 30-kw compressor from p1 to p2. the air temperature is maintained constant at 25 degrees c

  The pressure of the air in the cylinder is 140kpa model

air in contained in a vertical cylinder fitted with a frictionless piston and two sets of stops. the volume is .05m3

  Calculate the exact integration result using matlab

Calculate the exact integration result using Matlab symbolic tools and calculate the errors in calculating work done

  Nitrogen gas at 60 kpa and 7deg c enters an adiabatic

nitrogen gas at 60 kpa and 7deg c enters an adiabatic diffuser steadily with a velocity of 275 ms and leaves at 85 kpa

  The setup is such that pressure is proportional to volume p

a spring-loaded pistoncylinder assembly contains water at 500 c and 3 mpa. the setup is such that pressure is

  Pool ball b is to be shot into the side pocket d by

pool ball b is to be shot into the side pocket d by banking it off the cushion at c. specify the location x of the

  A force is described as 150 lb acting through the origin

a force is described as 150 lb acting through the origin of a two dimensional coordinate system up at an angle 135ordm

  Determine the maximum height h achieved the total flight

an experimental fireworks shell is launched vertically from point a with an initial velocity of magnitude v0 140

  You are to supply a design for an engine room crane

You are to supply a design for an engine room crane which will provide maintenance support for the main engine. Your design should include the rails the crane will sit on.

  The boiler is sized to provide a steam flow of 50 kgs

a simple ideal rankine cycle with water as the working fluid operates between the pressure limits of 3 mpa in the

  The weight of all other links is negligible at the instant

the compressor mechanism shown in figure is driven clockwise by a dc electric motor at a constant rate of 800 rpm. in

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd