An isentropic steam turbine processes 5kgs of steam at 4mpa

Assignment Help Mechanical Engineering
Reference no: EM13631097

An isentropic steam turbine processes 5kg/s of steam at 4Mpa. The majority of this steam is exhausted at 50kPa and 100 degree Celsius. Five percent of the steam is diverted for feedwater heating at 700kPa. Determine the power produced by the turbine in kW. Show the process on a T-s diagram.

Reference no: EM13631097

Questions Cloud

Archaeologists often find only parts of ancient human : archaeologists often find only parts of ancient human remains. for example they may find a small finger bone called the
A completely reversible refrigeration cycle removes heat at : a completely reversible refrigeration cycle removes heat at a rate of 100kw from an industrial refrigerator maintained
During the process the pressure and specific volume are : water vapor in a piston-cylinder assembly undergoes a process from saturated vapor at 150 c to a pressure of 300 kpa.
A 45 wt pb-55 mg alloy is rapidly quenched to room : a 45 wt pb-55 mg alloy is rapidly quenched to room temperature from an elevated temperature in such a way that the high
An isentropic steam turbine processes 5kgs of steam at 4mpa : an isentropic steam turbine processes 5kgs of steam at 4mpa. the majority of this steam is exhausted at 50kpa and 100
Your family grows over time and the required water supply : suppose you build a rural house where you need to run a pipe to the nearest water supply which fortunately is about 1
If the maximum temperature of the cycle is 2200k determine : consider an air standard otto cycle with a compression ratio of 8. the engine inlet conditions are p100 kpa t290k and
At location one fluid with a density of 121times103 kgm3 is : the equation of continuity states the mass flow rate has the same value at every position along a tube that has a
A car with a mass of 1570 kg is supported by four springs : a car with a mass of 1570 kg is supported by four springs each with a spring constant of 25 nmm. in traveling over an

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A levitation fan has been selected that delivers this

a hovercraft has a square planform a mass of 1.8 kg and has a plenum pressure requirement of 125 pa. a levitation fan

  P8mpa and t500 degc and leaves at 40 kpa as saturated vapor

p8mpa and t500 degc and leaves at 40 kpa as saturated vapor. if the flow rate is 11.1 kgs and the power generated by

  Helium at 810 r 45 ibfin2 and a velovity of 10 fts enters

helium at 810 r 45 ibfin2 and a velovity of 10 fts enters an insulated nozzle operating at steady state and exits at

  What pressure differential in inches of hg should exist

an 8-in. id 20.32 cm pipe is connected by means of a reducer to a 6-in id pipe. kerosene flows throught the system at

  The nitrogen is compressed to frac12 of the initial volume

two kg of nitrogen at 40degc and 200 kpa are contained in a frictionless piston-cylinder device. the nitrogen is

  At the same time measurements showed that the pipe

during drilling of a deep oil well the drill pipe got rigidly stuck. it was necessary to determine the depth at which

  If f1 110n f2 121n and f3 85n determine the magnitude

if f1 110n f2 121n and f3 85n determine the magnitude and coordinate direction angles of the resultant couple

  A log with a specific gravity of 067 is floating in water

a log with a specific gravity of 0.67 is floating in water. determine the percentage of the volume of the log that is

  A house has a composite wall of plaster board lp 10mm k072

a house has a composite wall of plaster board lp 10mm k0.72 wm.k fibre glass insulation lb100mm k1.4 wm.k and plywood

  Water at 70 kpa and 100 c is compressed isentropically in

water at 70 kpa and 100 c is compressed isentropically in a closed system to 5 mpa.determine the final temperature of

  The gas undergoes a quasistatic process according to the

a heavily insulated piston-cylinder device contains a gas which is initially at 5 bars and 187 degc and occupies 0.1

  Calculate the number of vacancies per cubic meter in some

calculate the number of vacancies per cubic meter in some metal at 689degc. the energy for vacancy formation is 0.75

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd