If the allowable shear stress in the bolt is 13000 psi what

Assignment Help Mechanical Engineering
Reference no: EM13625845

A horizontal beam AB with cross-sectional dimensions (b = 0.75 in) x (h = 8.0 in.) is supported by an inclined strut CD and carries a load P = 2700 lb at joint B. The strut, which consists of two bars each of thickness 5b/8, is connected to the beam by a bolt passing through the three bars meeting at joint C.

(a) If the allowable shear stress in the bolt is 13,000 psi, what is the minimum required diameter d(min) of the bolt at C?

(b) If the allowable bearing stress in the bolt is 19,000 psi, what is the minimum required diameter d(min) of the bolt at C?

Reference no: EM13625845

Questions Cloud

For a random sample of 50 measurements on the breaking : for a random sample of 50 measurements on the breaking strength of cotton threads the mean breaking strength was found
A truncated cone 20 cm high is constructed of aluminum the : a truncated cone 20 cm high is constructed of aluminum. the diameter at the top is 8 cm and the diameter at the bottom
The thermistors are to be sorted with those having : at a temperature of 25 degrees c the resistances of a type of thermistor are normally distributed with a mean of 10000
A 285 g bullet strikes a 0520 kg block attached to a fixed : a 28.5 g bullet strikes a 0.520 kg block attached to a fixed horizontal spring whose spring stiffness constant is
If the allowable shear stress in the bolt is 13000 psi what : a horizontal beam ab with cross-sectional dimensions b 0.75 in x h 8.0 in. is supported by an inclined strut cd and
The selection of a proper seller is critical to the success : the selection of a proper seller is critical to the success of a project. all of the below would be considered good
A golfer hits a golf ball with an initial velocity of 160 : a golfer hits a golf ball with an initial velocity of 160 fts at an angle of 25deg with the horizontal. knowing that
A 1200 kg cannon fires a 1000 kg cannonball at 35 ms what : a 1200 kg cannon fires a 100.0 kg cannonball at 35 ms. what is the recoil velocity of the cannon? assume that
Suppose you are conducting a study with a total of 50 : suppose you are conducting a study with a total of 50 participants from five different regions of the country and you

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The wall of a cold storage consists of three layers- an

the wall of a cold storage consists of three layers- an outer layer of ordinary bricks 25 cm thick a middle layer of

  A horizontal circular cylinder of diameter d 02m and

a horizontal circular cylinder of diameter d 0.2m and length 2m is elastically mounted on two springs and towing tank

  In an accelerator protons emerge with velocity of 25 x 108

in an accelerator protons emerge with velocity of 2.5 x 108 ms. the accelerator is 0.8km long.a if the acceleration is

  A 10 cm x 10cm sheet of material is 2 cm thick and made of

a 10 cm x 10cm sheet of material is 2 cm thick and made of a material with a conductivity of 0.5wmk?. one side of this

  Estimate the speed of the body

A 15cm cube of mass 3kg is lubricated with SAE 10 oil at 20oC (dynamic viscosity of 0.104Ns/m2) slides down a 10o inclined plane at a constant velocity. Estimate the speed of the body if the oil film has a thickness of 2mm and the velocity distrib..

  The compressor pressure ratio is 117 and the temperature at

a pure jet engine propels an aircraft at 330 ms through air at 60 kpa and 0 degrees celsius. the inlet diameter of this

  A child of mass 20 kg is standing on a plank inclined at

a child of mass 20 kg is standing on a plank inclined at 20 degrees to the horizontal. how much force does the child

  If the barometric pressure was 100 kpa and the humidity was

temperature in state college pa on 31st december 2012 was 22 f. if the barometric pressure was 100 kpa and the humidity

  Finally compressed at the constant pressure to the initial

a piston-cylinder device contains 0.15kg of air initially at 2mpa and 350oc. the air is first expanded isothermally to

  On top of the water is 03 m of kerosene which is open to

water occupies the bottom 0.8 m of a cylindrical tank. on top of the water is 0.3 m of kerosene which is open to the

  A piston cylinder device contains 05 kg of water at 10mpa

a piston cylinder device contains 0.5 kg of water at 1.0mpa and 400oc. now it is cooled to 1mpa in sat-v phase.

  What is the angular velocity wcd

What is the angular velocity Wcd (t)?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd