A truncated cone 20 cm high is constructed of aluminum the

Assignment Help Mechanical Engineering
Reference no: EM13625848

A truncated cone 20 cm high is constructed of aluminum. The diameter at the top is 8 cm, and the diameter at the bottom is 12cm. The lower surface is maintained at 100 degree celcius; the upper surface , at 500 degrees celcius. The other surface is insulated. Assuming one dimensional flow, what is the rate of heat transfer in watts?

Reference no: EM13625848

Questions Cloud

The still is supposed to produce a distillate containing 75 : a saturated-liquid mixture of benzene and toluene containing 50 mol benzene is distilled in an apparatus consisting of
A 5 cm layer of insulation with thermal conductivity of : a 5 cm layer of insulation with thermal conductivity of 0.06 wm.c is placed between two plates of 100 and 200 degrees
What does she calculate for the minimum thickness of the : a researcher measures the thickness of a layer of benzene floating on water by shining mono- chromatic light onto the
For a random sample of 50 measurements on the breaking : for a random sample of 50 measurements on the breaking strength of cotton threads the mean breaking strength was found
A truncated cone 20 cm high is constructed of aluminum the : a truncated cone 20 cm high is constructed of aluminum. the diameter at the top is 8 cm and the diameter at the bottom
The thermistors are to be sorted with those having : at a temperature of 25 degrees c the resistances of a type of thermistor are normally distributed with a mean of 10000
A 285 g bullet strikes a 0520 kg block attached to a fixed : a 28.5 g bullet strikes a 0.520 kg block attached to a fixed horizontal spring whose spring stiffness constant is
If the allowable shear stress in the bolt is 13000 psi what : a horizontal beam ab with cross-sectional dimensions b 0.75 in x h 8.0 in. is supported by an inclined strut cd and
The selection of a proper seller is critical to the success : the selection of a proper seller is critical to the success of a project. all of the below would be considered good

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the work in kjkg done per unit mass of the steam

steam at 2.5 mpa and 400 c enters an adiabatic steam turbine with a low velocity and leaves with a velocity of 180 ms

  The rods are connected with gears having radii of 120 and

the rods ab and cd each have a 30-mm diameter and are 1m long. the modulus of the rods is 28 gpa. the rods are

  Determine the average temperature of the cooling water can

a cylindrical nuclear fuel rod of 1 cm in diameter is encased in a concentric tube of 2 cm in diameter where cooling

  Find an expression for the torsional constant k in terms of

a thin metal disk of mass m2.00 x 10-3 kg and radius r2.20cm is attached at its center to a long fiber. when the disk

  An open feed water heater incorperated with the steam cycle

consider a combined gass steam power plant that has a net power output of 450 mw. the pressue ratio of the gas turbine

  The relationship between pressure and volume during the

oxygen o2 gas within a piston-cylinder assembly undergoes an expansion from a volume v1 0.01 m3 to a volume v2 0.03

  A piston-cylinder device initially contains 50 l of liquid

a piston-cylinder device initially contains 50 l of liquid water at 40 degrees c and 200 kpa. heat is transferred to

  The velocity of the air stream decreases from 230 ms to 30

nitrogen gas at 60 kpa and 7 degrees celsius enter an adiabatic diffuser steadily with a velocity of 195 ms and leaves

  Saturated liquid water at 1 kgs and 200 kpa is mixed

saturated liquid water at 1 kgs and 200 kpa is mixed steadily with 4 kgs of water at 200 kpa and 200ordmc with the goal

  Determine the angular velocity and angular acceleration

Block B of the mechanism is confined to move within the slot member CD. If AB is rotating at a constant rate of AB = 3rad/s, determine the angular velocity and angular acceleration of member CD at the instant shown.

  What is the yield strength

If the critical resolved shear stress is 10 MPa, what is the yield strength?

  What would the mole and mass fractions be if she was to

a combustion engineer wishes to produce an inert mixture to replace normal air. she will do that using a mixture of n2

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd