If 002 kg leaks out and the temperature drops to 27oc find

Assignment Help Mechanical Engineering
Reference no: EM13626942

Carbon monoxide is initially in a 50 L tank at 210 kPA and 127C.

a) Determine the mass of the gas, in kilograms.

b) If 0.02 kg leaks out and the temperature drops to 27OC, find the gage pressure in the tank if the barometric pressure is 98.8 kPa.

Reference no: EM13626942

Questions Cloud

Determine the minimum pipe diameters required to restrict : consider a steam turbine in which steam enters at 10.45 mpa and 780k with a flow rate of 38.739 kgs. a portion of the
Assume that a signal passes through an opening of 423 m : in conventional television signals are broadcast from towers to home receivers. even when a receiver is not in direct
A truck traveling at vo 60mph when the driver applies the : a truck traveling at vo 60mph when the driver applies the brakes to come to stop the deceleration of the truck is
Consider a concentric circular-tube annulus with outer : consider a concentric circular-tube annulus with outer diameter 2.5cm and inner diameter 1.25cm in which air is flowing
If 002 kg leaks out and the temperature drops to 27oc find : carbon monoxide is initially in a 50 l tank at 210 kpa and 127c.a determine the mass of the gas in kilograms.b if 0.02
Airlines sometimes overbook flights suppose that for a : airlines sometimes overbook flights. suppose that for a plane with 50 seats 55 passengers have tickets. define the
If the discharge piping of the pump runs vertically upward : a pump raises the pressure of water from 100 kpa to 900 kpa and raises the velocity from 1 ms to 20 ms. the flow rate
According to the national association for college : according to the national association for college admissions counseling and usa today. 19.8 of college students take at
There are so-called unwritten laws of engineering that : there are so-called unwritten laws of engineering that recommend acceptable conduct and behavior for engineers in

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compute the maximum tensile stress due to the bars own

a 100-ft-long steel bar is suspended vertically from its upper end. the cross-sectional area of the bar is 4.0 in.

  Estimate the screw torque erquired to raise the load if

a square-threaded power screw with single thread is used to raise a load of 25000lb. the screw has a mean diameter of 1

  Suppose he hit the ball with a speed of 23 ms at an angle

on the apollo 14 mission to the moon astronaut alan shepard hit a golf ball with a golf club improvised from a tool.

  The engine is used to drive an electrical generator that is

1. an aluminum casting that weighs 10 pounds sits on a steel surface. how much force will be necessary to get it to

  What is the maximum temperature gradient in the glass

How long wi1l it take for the mid plane temperature to achieve 50% of its maximum possible temperature reduction?

  Derive the following a differential equation between input

the following data were observed in a step response experiment of a thermometer is under a step input from 0 degress c

  Find the power input to the compressor suppose on an actual

air flows through an adiabatic internally reversible compressor at a rate of 0.04 kgs. at the inlet thepressure is 200

  Calculate the radius of a vanadium atom given that v has a

calculate the radius of a vanadium atom given that v has a bcc crystal structure a density of 5.96gcm3 and an atomic

  3kg of r22 in a piston-cylinder is initially at a pressure

1 steam at 3 mpa and 400 c enters an adiabatic nozzle steadily with a velocity of 40 ms and leaves at 2.5 mpa and 300

  If upon initial null balance r3 is 1275 ohms and if when r2

a simple wheatstone bridge as shown in fig. 7.10 is used to determine accurately the value of an unknown resistance r1

  Consider uniform potential flow past an ellipse with

consider uniform potential flow past an ellipse with thickness ratio t. use an appropriate joukowski transformation to

  Fr an output power of 316 hp we have nm 1483 rpm and ia

a shunt dc motor has ra 0.3 u03a9 and vt 999.9 v. for an output power of 31.6 hp we have nm 1483 rpm and ia 145.8 a.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd