Consider a concentric circular-tube annulus with outer

Assignment Help Mechanical Engineering
Reference no: EM13626943

Consider a concentric circular-tube annulus, with outer diameter 2.5cm and inner diameter 1.25cm, in which air is flowing under fully developed, heat rate conditions. Heat is supplied to the inner tube, and the outer tube is externally insulated. The radiation emissivity of both tube surfaces is 0.8. The mixed mean temperature of the air at a particular point in question is 260C. The inner-tube surface temperature at this point is 300C. What is the total heat flux from the inner-tube surface at this point? What is the outer-tube surface temperature at this point? What percentage of the heat supplied to the inner tube is transferred directly to the air, and what percentage indirectly from the outer surface?

Reference no: EM13626943

Questions Cloud

Assume that salaries are normally distributed the standard : according to salary wizard the average base salary for a brand manager in houston texas is 88592 and the average base
Determine the minimum pipe diameters required to restrict : consider a steam turbine in which steam enters at 10.45 mpa and 780k with a flow rate of 38.739 kgs. a portion of the
Assume that a signal passes through an opening of 423 m : in conventional television signals are broadcast from towers to home receivers. even when a receiver is not in direct
A truck traveling at vo 60mph when the driver applies the : a truck traveling at vo 60mph when the driver applies the brakes to come to stop the deceleration of the truck is
Consider a concentric circular-tube annulus with outer : consider a concentric circular-tube annulus with outer diameter 2.5cm and inner diameter 1.25cm in which air is flowing
If 002 kg leaks out and the temperature drops to 27oc find : carbon monoxide is initially in a 50 l tank at 210 kpa and 127c.a determine the mass of the gas in kilograms.b if 0.02
Airlines sometimes overbook flights suppose that for a : airlines sometimes overbook flights. suppose that for a plane with 50 seats 55 passengers have tickets. define the
If the discharge piping of the pump runs vertically upward : a pump raises the pressure of water from 100 kpa to 900 kpa and raises the velocity from 1 ms to 20 ms. the flow rate
According to the national association for college : according to the national association for college admissions counseling and usa today. 19.8 of college students take at

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd